Overview
The G2 Axle and Gear 95-2010-001 is a GM 9.5 inch 14 bolt rear axle shaft with 33 splines for 1981–1991 Chevrolet and GMC CK20 trucks. G2 says its high strength axle shafts are engineered for the added load of high torque applications and to fix common faults of factory shafts. The company states they are forged from high grade alloy steel, heat treated to exceed OEM specifications, and offer Big Spline options and rolled splines so owners can run larger tires without risk of failure.
The 95-2010-001 fits either side of the GM 14 bolt rear axle and takes 9/16in press fit wheel studs. The studs are not included with the shaft.
Key features
- Rear axle shaft for the GM 9.5 inch 14 bolt axle
- 33 splines
- Fits driver or passenger side
- Forged from high grade alloy steel.
- Heat treated beyond OEM specifications.
- Uses 9/16in press fit wheel studs
Pressing in studs and axle care
Press-fit studs need the right tools and a steady hand. The stud should seat square in the flange with the knurled section fully pressed, and the shaft should be supported so the flange is not bent. A stud that is pressed in crooked can loosen under load, so check each one for straightness before fitting the wheel.
Old axles often show wear at the bearing and seal areas when they are pulled. Look for pitting on the spline, grooves on the shaft and grease leaking from the axle tube, since these point to a worn bearing or seal that should be replaced at the same time. A new shaft sitting on worn bearings can wear quickly, so inspect the bearing before reassembly and keep the axle lubricated with the correct gear oil.
- Check each stud for straightness before pressing
- Inspect the spline for pitting or grooves
- Look for grease or oil leaks at the axle tube
Specifications
| Brand | G2 Axle and Gear |
|---|---|
| Part number | 95-2010-001 |
| UPC | 631410106107 |
| Axle manufacturer | GM |
| Shaft location | Driver Or Passenger |
| Axle position | Rear |
| Axle type | GM 14 Bolt 9.5 Inches |
| Position | Rear |
| Spline count | 33 Splines |
| Wheel stud size | 9/16in press fit |
| Material | High grade alloy steel, forged |
| Applications noted | 1981-1991 CK20 |
Vehicle fitment
It is for Chevrolet and GMC three-quarter-ton trucks across the models and years below. Other GM trucks and other axle sizes are not covered.
- 1981–1986 Chevrolet C20 (Cheyenne, Custom, Deluxe, Scottsdale, Silverado)
- 1988–1992 Chevrolet C2500 (Cheyenne, Scottsdale, Silverado)
- 1981–1986 Chevrolet K20 (Cheyenne, Custom, Deluxe, Scottsdale, Silverado)
- 1988–1992 Chevrolet K2500 (Cheyenne, Scottsdale, Silverado)
- 1987–1988 Chevrolet R20 (Cheyenne, Custom Deluxe, Scottsdale, Silverado)
- 1989 Chevrolet R2500 (Cheyenne, Scottsdale, Silverado)
- 1987 Chevrolet V20 (Custom Deluxe, Scottsdale, Silverado)
- 1981–1986, 1988–1991 GMC C2500 (Base, High Sierra, Sierra, Sierra Classic, Sierra Grande, Sierra SLE, Sierra SLX)
- 1981–1986, 1988–1991 GMC K2500 (Base, High Sierra, Sierra, Sierra Classic, Sierra Grande, Sierra SLE, Sierra SLX)
- 1987–1989 GMC R2500 (Base, High Sierra, Sierra Classic)
- 1987 GMC V2500 (Base, High Sierra, Sierra Classic)
The models and years above are covered, with gaps such as 1987 for the C20 and K20. Other GM trucks and other axle sizes are not covered. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
Plan to press 9/16in studs into the new shaft yourself, since G2 supplies the shaft without them.
What’s included
One rear axle shaft.
Not included: wheel studs.








