Select your vehicle

G2 Ford 7.5 Inch 3.08 Ratio Ring and Pinion – 2-2014-308

G2 Axle and Gear

Shop G2 Axle And Gear Ring And Pinions on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Ring and pinion set for the Ford 7.5 Inch rear axle
  • Gear ratio 3.08, part number 2-2014-308
  • Designed for oversized tires and high-performance engines
  • No vehicle list; match the 7.5 Inch housing

Description

Overview

The G2 Axle and Gear 2-2014-308 is a 3.08 ratio ring and pinion for the rear Ford 7.5 Inch axle. A 3.08 ratio is a numerically lower setting than the 4.10 and 5.13 sets in the same range, so the pinion turns 3.08 times for each ring gear revolution, which favors highway speed and lower engine rpm.

G2 says its Performance Ring and Pinion line is made for demanding use, including oversized tires and high-performance engines, and that it uses current materials and manufacturing methods. The set is identified by the 7.5 Inch Ford axle rather than by a vehicle model, so the axle housing is the first check.

Key features

  • 3.08 gear ratio for the Ford 7.5 Inch rear axle
  • Ring gear and pinion supplied together as one set
  • Designed for oversized tires and high-performance engines.
  • It is made with current materials and manufacturing methods.
  • Rear axle location

Driving with a 3.08 set

A 3.08 ratio is a numerically lower gear, so the engine turns more slowly at a given road speed than it would with a higher ratio. That suits steady highway driving, where lower rpm can mean quieter operation and less strain on the engine. The trade-off is slower acceleration from a stop and reduced pulling force at low speed, which matters for towing, steep grades and off-road crawling.

A gear swap is a good time to inspect the rest of the axle. Look at the axle shafts, bearings and seals while the cover is off. Replacing worn carrier bearings and the pinion seal with the new gears avoids opening the housing again soon after the job is done.

  • Match the gear ratio to how the vehicle is used most
  • Check axle seals and shaft bearings during the swap
  • Keep the cover gasket clean and flat before reassembly
  • Inspect the housing for cracks around the carrier bolts

Specifications

Brand G2 Axle and Gear
Part number 2-2014-308
UPC 631410105186
Axle type Ford 7.5 Inches
Axle location Rear
Gear ratio 3.08
Axle manufacturer Ford

Vehicle fitment

The set is matched to the Ford 7.5 Inch rear axle. Identify that housing and its carrier on your vehicle before ordering, since the axle type decides fit.

Confirm your vehicle’s year, model and trim before ordering.

Installation notes

Backlash and tooth contact must be set with precise measurement, so a gear shop equipped for ring and pinion work is the usual choice. Run the new gears in gradually before sustained highway loads.

What’s included

One ring and pinion set for the Ford 7.5 Inch axle, part number 2-2014-308.

Not included: Carrier bearings and pinion shims are sold separately and may be needed for the installation.

SKU: G/22-2014-308 Category:

Specification

Shipping weight 15.00 lbs
Package dimensions 12.00 × 11.00 × 5.50 in
brands

Questions & Answers

Is the G2 2-2014-308 made for the Ford 7.5 Inch axle?

Yes, G2 names the Ford 7.5 Inch rear axle for this 3.08 set. No vehicle models are listed, so confirm your housing type before ordering.

What does a 3.08 ratio mean for driving?

The pinion turns 3.08 times per ring gear turn. Compared with numerically higher sets, it keeps engine rpm lower at a given road speed.

Are installation parts supplied?

No. Carrier bearings and shims are sold separately, so check what your carrier needs and buy those parts before the installation begins.

Is a 3.08 set a good choice for a daily driver?

It suits driving where highway speed matters more than hard launches, since engine rpm stays lower. Off-road or towing use may call for a numerically higher set, so compare the ratio against how the vehicle is driven.

What should be checked after a gear swap?

Check for leaks at the cover and axle seals, listen for whine during the first drives, and recheck cover bolts after a short run. Confirm the tooth contact was set correctly before heavy use.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop G2 Axle And Gear Ring And Pinions on Amazon