Select your vehicle
-13%

G2 Dana 80 3.54 Ratio Ring and Pinion – 2-2080-354

G2 Axle and Gear

Shop G2 Axle And Gear Ring And Pinions on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • G2 Axle and Gear 3.54 ratio ring and pinion for the Dana 80 rear axle, part 2-2080-354
  • For use with 3.73 and down carriers
  • Computer heat treated 8620 steel, double shot peened, double lapped
  • Check with the vehicle manufacturer for proper fitment

Description

Overview

This is a 3.54 ratio ring and pinion for the Dana 80 rear axle. It works with 3.73 and down carriers. Confirm the axle size and carrier before ordering.

G2 describes its gear sets as built for oversized tires and high performance engines. This 3.54 Dana 80 set uses computer heat treated 8620 steel with double shot peened and double lapped surfaces, and it is manufactured to O.E. specifications.

Key features

  • 3.54 ratio for the Dana 80 rear axle
  • For use with 3.73 and down carriers
  • Computer heat treated 8620 steel
  • Double shot peened surfaces
  • Double lapped gear set
  • Manufactured to O.E. specifications
  • 10 year warranty from G2

Maintenance and setup

A Dana 80 rear axle is a heavy-duty unit, and the ring and pinion carries the full drive load. Replacing the gears is a good time to inspect the axle housing, axle shafts, and bearings. Look for chipped teeth or metal in the oil, which point to wear that will not improve on its own.

A 3.54 ratio pulls less hard at low speed than a numerically higher setup, so the choice depends on tire size and use. Keep fresh gear oil in the axle, and retighten the cover bolts after the first trail runs. A driveline shop can check pinion depth and preload for a clean first run.

  • Replace the pinion seal during the job
  • Check the axle shafts and bearings
  • Use the correct gear oil for the Dana 80

Specifications

Brand G2 Axle and Gear
Part number 2-2080-354
UPC 631410105254
Gear ratio 3.54
Axle location Rear
Axle type Dana 80
Popular axle manufacturer Dana
Carrier requirement 3.73 and down
Material Computer heat treated 8620 steel

Vehicle fitment

This set is for the Dana 80 rear axle at a 3.54 ratio. Verify the axle housing against your vehicle before buying.

This set is for the Dana 80 only, so other Dana axle sizes need their own ring and pinion.

Installation notes

Dana 80 gears need pinion depth, backlash and bearing preload set by a driveline shop, and a break-in period before the 3.54 ratio is loaded.

What’s included

A matched ring and pinion for the Dana 80 rear axle.

SKU: G/22-2080-354 Category:

Specification

Shipping weight 20.00 lbs
Package dimensions 12.00 × 11.00 × 5.50 in
brands

Questions & Answers

Will the 2-2080-354 ring and pinion fit my Dana 80 axle?

It is for the Dana 80 rear axle with a 3.73 and down carrier. Check the axle housing before ordering, since fit depends on your vehicle.

Which carrier should I use with this 3.54 set?

Use a carrier at or below 3.73. Check the carrier ratio before installing, since this set is meant for 3.73 and down carriers.

Does the set include the carrier?

No carrier is included. The set is a ring and pinion made from computer heat treated 8620 steel, with a 10 year warranty.

Does a Dana 80 ring and pinion need extra attention?

Dana 80 axles carry heavy loads, so check the pinion seal, cover bolts, and gear oil level after the first trail runs. Metal in the oil or a change in noise is a reason to open the axle for inspection.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop G2 Axle And Gear Ring And Pinions on Amazon