Select your vehicle

Front Drive Shaft

Point Spring And Drive Shaft Co.

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Point Spring and Drive Shaft Co. front drive shaft, part number POI5360986
  • Stock length, non-CV, no slip yoke eliminator needed
  • Fits 4, 6 or 8 cylinder engines and T-4, T-5 and T-170 transmissions
  • Fits 1980–1983 Jeep CJ5, 1980–1986 CJ7 and 1981–1985 Scrambler

Description

Overview

The Point Spring and Drive Shaft Co. POI5360986 is a stock length, non-CV front drive shaft for the 1980–1983 Jeep CJ5, the 1980–1986 Jeep CJ7 and the 1981–1985 Jeep Scrambler.

Measure your existing shaft against the 29-1/2 collapsed and 31-1/4 running lengths before fitting. The shaft fits 4, 6 or 8 cylinder engines and the T-4, T-5 and T-170 transmissions.

Key features

  • Stock length front drive shaft
  • Non-CV design
  • No slip yoke eliminator required
  • Fits 4, 6 or 8 cylinder engines

Driveline fit and checks

The front drive shaft carries power from the transfer case to the front axle, and its length and joint type determine how it sits under the vehicle. A non-CV design uses a simpler joint setup than constant velocity joints, which suits stock front axles. Measuring the existing shaft’s collapsed and running lengths helps confirm a match before the old one is removed.

Worn U-joints or a bent shaft often show up as vibration at road speed or a clunk when engaging four-wheel drive. Inspect the joints for play, look for grease leaks, and check the yokes for wear. When a shaft is replaced, the slip yoke and the transfer case seal are good places to inspect as well.

  • Feel for play in each joint
  • Check for grease leaks at the seals
  • Look for a bent or dented tube

Specifications

Brand Point Spring and Drive Shaft Co.
Part number POI5360986
Position Front
Length Stock
Collapsed length 29-1/2
Running length 31-1/4
Joint type Non-CV
Slip yoke eliminator Not required
Engines 4, 6 or 8 cylinder
Transmissions T-4, T-5 and T-170
Fitment type Direct fit

Vehicle fitment

It fits the 1980–1983 Jeep CJ5, the 1980–1986 Jeep CJ7 and the 1981–1985 Jeep Scrambler.

The Scrambler and CJ models are older Jeep platforms, and the list does not include the Wrangler YJ or later models. Confirm your vehicle’s year, model and trim before ordering.

What’s included

The front drive shaft.

Fitment

VehicleYearsTrims
Jeep CJ51980–1983Base, Golden Eagle, Laredo, Limited, Renegade
Jeep CJ71980–1986Base, Golden Hawk, Laredo, Limited, Renegade
Jeep Scrambler1981–1985Base, Laredo, Renegade, SL, SR

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Will the POI5360986 fit a 1985 Jeep CJ7?

Yes. It fits the 1980–1986 Jeep CJ7, so a 1985 CJ7 is within that range. Confirm the engine and transmission match the 4, 6 or 8 cylinder and T-4, T-5 or T-170 setup before ordering.

Does this shaft need a slip yoke eliminator?

No. It is a non-CV design at stock length, so no slip yoke eliminator is needed for installation. Confirm your drivetrain setup before ordering.

What engines and transmissions does it fit?

It fits 4, 6 or 8 cylinder engines and the T-4, T-5 and T-170 transmissions. Confirm your engine and transmission match those options before ordering, and check your vehicle's year, model and trim.

What are signs a front drive shaft needs attention?

Vibration at speed, a clunk when engaging four-wheel drive, and grease leaks at the joints all point to wear. Inspect the U-joints and yokes, and replace worn parts before they fail on the trail.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon