Select your vehicle

Fabtech 6 Inch Basic Lift Kit w/Performance Shocks – K7024

Fabtech

Shop Toyota FJ Cruiser Lift Kits on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • 6 inch Crawler system for the 2010–2012 Toyota FJ Cruiser
  • Radius arm front conversion with 5/16 inch steel links and urethane joints
  • Trac bar relocation at both ends of the vehicle
  • Replacement shock mounts add 1 inch of ground clearance at the rear
  • Designed for 35/12.50R17 tires; part number K7024

Description

Overview

The Fabtech K7024 is a 6 inch Crawler lift kit for the 2010–2012 Toyota FJ Cruiser. It is designed for off-road builds that run 37 inch tires. The front converts the factory four-link suspension to a radius arm design, and the rear keeps the factory five-link layout with extended length lower arms.

This kit suits a rock crawling or serious trail build. The radius arm links are made of 5/16 inch thick steel with rotational urethane joints for unrestricted articulation, and the front lift uses coil springs or coilovers.

Key features

  • Front radius arm links of 5/16 inch thick steel with rotational urethane joints at each end
  • 1/4 inch thick steel crossmember that bolts to the frame under the transmission
  • Dropped pitman arm and relocated trac bar bracket to reduce bump steer
  • Rear tubular lower arms and tubular upper links with adjustable rotational urethane ends
  • Replacement shock mounts that allow trimming of the factory mounts for 1 inch of extra ground clearance at the rear
  • Heavy duty replacement driveshafts are available for use with the system

Trail use and maintenance

A radius arm front conversion changes how the axle is located, so the links, bushings and mounts carry the load that the factory parts used to share. Rotational urethane joints allow more travel, but they also need periodic inspection for tears, cracks and loose hardware, especially after hard articulation on rocks.

Driveline angles matter more on a lifted FJ Cruiser than on a stock one. Check the CV joints and driveshaft U-joints after each serious trail outing, and keep the transfer case vent and differential breather clear of mud and water.

Shock mounts and bump stops are often the first parts to show stress on hard trails. Inspect the trimmed mounts for cracks, and recheck the alignment after any part is replaced. Many builders also replace worn tie rod ends at the same time as the radius arms, since they affect steering geometry on the same side of the vehicle.

Specifications

Brand Fabtech
Part number K7024
UPC 70000639215
Suspension type Knuckle, with radius arm front conversion
Rear lift method Spacers
Lift height range 5 to 6.99 inches
Radius arm link thickness 5/16 inch steel
Crossmember thickness 1/4 inch steel
Tire guidance 35/12.50R17 on 17×8 wheels, 4 5/8 inch backspace, minor trimming

Vehicle fitment

It fits the 2010–2012 Toyota FJ Cruiser.

FJ Cruiser model years outside 2010–2012 are not covered. The kit does not fit models with factory electronic controlled shocks. Compare your vehicle’s year, model and trim with this fit before ordering.

Installation notes

This is a full suspension conversion, not a spacer lift. The front and rear links change the factory geometry, so driveshaft angles and alignment must be checked after installation. The replacement shock mounts may need trimming on the factory mounts, and heavy duty driveshafts are needed for correct drivetrain angles.

What’s included

The kit’s parts are the radius arm links, the front crossmember, the dropped pitman arm, the trac bar brackets, the rear tubular arms and upper links, and the replacement shock mounts. Coil springs or coilovers for the front lift are needed separately.

Not included: Heavy duty driveshafts, which Fabtech offers as an option for this system, and tires and wheels.

SKU: FABK7024 Category:

Specification

Shipping weight 310.10 lbs
Package dimensions 0.00 × 0.00 × 0.00 in
brands

Fitment

VehicleYearsTrims
Toyota FJ Cruiser2010–2012Base

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Will the Fabtech K7024 fit a 2013 FJ Cruiser?

No. It fits 2010–2012 FJ Cruisers only, so other model years fall outside its coverage. Confirm fit for your vehicle before ordering.

Does the K7024 work with factory electronic shocks?

No. The kit does not fit models with factory electronic controlled shocks. Check whether your FJ Cruiser has them before ordering the radius arm system.

What tires does the K7024 work with?

The kit is used with 35/12.50R17 tires on 17x8 wheels with a 4 5/8 inch backspace, with minor trimming. It is intended for aggressive off-road use with 37 inch tires.

How often should radius arm bushings be inspected?

Inspect them after every serious trail outing and at each regular service. Look for cracking, torn urethane, play in the joints and loose bolts. Replace worn ends before they affect steering or axle position.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Toyota FJ Cruiser Lift Kits on Amazon