Select your vehicle

Engine Parts

Internal engine parts and gaskets for older Jeep and similar engines, including timing sets, valve train parts, piston rings, seals, valve covers, flywheels and mounts. Most listings come from Crown Automotive and Omix-Ada.Subcategories split the range by engine family, such as CJ four-cylinder, AMC V8 and 4.0L six-cylinder. Open a product page for part numbers, then compare the listings on this page.

Crown Automotive timing kit for AMC 304-360 V8 engines

Keeping an older Jeep engine alive means finding the right seal, gasket or timing part for an engine that may be fifty years old. This section focuses on factory-style replacement parts for the AMC, Willys and Chrysler engines Jeep used.

Coverage runs from the 134 cubic inch L-head and F-head fours through the AMC 258 and 4.0L sixes and AMC V8s, plus some 3.6L and 3.8L V6 parts. The 1972–86 six-cylinder group is the largest and holds parts for several other engines too, so search by engine size rather than relying on the group name. Expect seals, gaskets, timing sets, valve train pieces, bearings, mounts and filters.

77Parts listed
2Brands
4Part types
134–401 ciEngine sizes covered
1/2"-13 x 3"Main cap bolt, AMC 4/6
5/8"AMC V8 sprocket width

Shop engine parts by engine

Popular engine parts

Jeep engine identification reference

Cubic inch and liter names for the engines this section covers, plus specs taken from listed parts. Many parts are labeled by one name or the other, so it helps to know both.

Engine names: cubic inches to liters

134 ci four (L-head, F-head)2.2L
AMC 150 four2.5L
AMC 258 six4.2L
AMC/Jeep 242 six4.0L
AMC 304 V85.0L
AMC 360 V85.9L
AMC 401 V86.6L
Chrysler 3.8L V6 (Wrangler JK)2007–2011
Pentastar V6 (Wrangler JK)3.6L, from 2012

Specs from listed parts

Main bearing cap bolt, 2.5L/4.0L/4.2L1/2"-13 x 3"
F-134 Hurricane crankshaft gear31 teeth
AMC 304–360 timing kit5/8" wide sprockets
134 four rod bearingsStandard or .010" oversize, pairs
5.2L / 5.9L valve cover grommet.45" inside diameter
3.6L lower intake gasket6 required per engine
Heavy-duty air intake duct28" long

Details that change the part

  • VAM (Mexican-built AMC) engines take different valve train parts
  • 4.2L heads with a studded rocker arm bridge use their own retainer nuts
  • Automatic (TorqueFlite) cars use a flex plate or auto flywheel, not a manual one
  • Some 4.2L intake ducts differ with and without power brakes
  • The JK 3.8L oil pan gasket is listed for coil-on-plug engines
  • Engine mounts are often sided; left and right carry different part numbers
  • Oil filters list SAE or metric threads; check before swapping brands

Confirm the engine by its build code or casting numbers before ordering. Many Jeep engines had running changes within a model year.

All Engine Parts 77 parts

Showing 1–12 of 77 resultsSorted by popularity

Engine parts by family

Engine parts are rarely interchangeable across families, so the first step is identifying the engine. The subcategories here separate older 6-cylinder engines from 1972 to 1986, CJ 4-cylinder engines, CJ and full-size V8 engines, and the 4.0L six-cylinder used in the TJ Wrangler. The sample products also include parts for the 2.5L four, the 3.8L V6, AMC 304 to 360 V8s and F-Head fours.

What you will find

Typical items cover most of a rebuild or a top-end refresh.

  • Timing sets and kits, including sprocket width details
  • Gaskets and seals such as valve cover, exhaust manifold and crankshaft rear seals
  • Valve train parts like push rods, valves and valve seals
  • Rotating assembly parts such as pistons, pins and ring sets
  • Covers and housings, flywheels, mounts and oil filters

Matching parts to your engine

Confirm displacement and cylinder count, the model year range, and any variation such as fuel system or transmission type. Listing notes such as 5/8 inch wide sprockets, torque flite automatic or driver versus passenger side exist because small differences prevent a part from fitting.

For rebuilds, check cylinder bore size and whether oversize pistons or rings are needed after machine work. Measure your original parts or consult the engine's service manual before ordering.

Rebuild and installation guidance

Replace seals and gaskets with new ones every time, and clean mating surfaces thoroughly. Use the torque sequence and values in the factory service manual, particularly for cylinder head, intake and exhaust manifold fasteners. Timing components must be set to their marks, and an error can cause serious engine damage.

When the engine is already apart, inspect related parts such as the oil pump, water pump and mounts. Engine work benefits from careful labeling and bagging of fasteners. If you are not comfortable with internal engine work, have a machine shop or qualified mechanic handle it.

Keep a written record of part numbers and measurements as you work, and take photos before disassembly. Engines in this age range often have several running changes within one model year, so a photo of the original part is a helpful way to confirm a match when the listing is ambiguous.

Gasket sealing, torque and break-in practices

The quality of an engine repair often depends on preparation. Clean gasket surfaces with a plastic scraper or the method the manufacturer recommends, because gouges in aluminum or cast iron cause leaks that no gasket can fix. Check that bolt holes are clean and dry, since oil or coolant trapped in a blind hole can crack a casting when a bolt is tightened.

  • Use the torque sequence from the service manual, normally starting at the center and moving outward in stages
  • Apply sealant only where the instructions call for it, since excess can block oil passages
  • Prime the oil system and lubricate the camshaft and lifters with assembly lube on a rebuild
  • Replace the oil and filter soon after a major repair
  • Check for leaks and watch coolant level and temperature after the first runs

After a rebuild, follow the recommended break-in for the first few hundred miles: varied engine speeds, no extended idling and no heavy towing. Keep an eye on oil pressure and listen for new noises. Older Jeep engines can be tolerant, but they depend on correct clearances and clean oil, so a patient first few tanks of fuel are worth it.

Popular Engine Parts brands

Engine Parts FAQ

How do I identify my Jeep engine?

Check the VIN, which includes an engine code, and the emissions label under the hood. Displacement can also be cast into the block or valve cover. Use these details to match the parts.

Should I replace the timing chain and gears together?

Yes. Replacing the chain, sprockets and tensioner components as a set avoids uneven wear, since a new chain on worn sprockets stretches quickly. Always follow the factory service manual limits for your engine.

Are gasket sets and individual gaskets the same?

A set bundles many gaskets for a job, while individual gaskets cover a single location. Check what the set includes against the work you are doing and note whether items are sold each.

Do I need to resurface the head when replacing a gasket?

It is wise to check head and block flatness with a straightedge. Warped surfaces cause leaks even with a new gasket, so machine work may be needed according to service manual limits. Machine shops can measure this precisely, so ask for a flatness check on any engine you are rebuilding or resealing.