Select your vehicle
-13%

Pro Comp PRO-M Monotube Rear Shock Absorber – PR2087

Pro Comp Suspension

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Fits Jeep CJ5 (1960–1983) and CJ7 (1976–1986)
  • Designed for CJ models with a 3 to 4 inch lift
  • 24.3-inch extended length, 15.6-inch collapsed length
  • PRO-M monotube rear shock with vehicle-specific valving
  • Polyurethane shock boot included

Description

Overview

The Pro Comp PR2087 is a PRO-M monotube rear shock absorber for the Jeep CJ5 (1960–1983) and CJ7 (1976–1986). It is designed for CJ models with a 3 to 4 inch lift, with a 24.3-inch extended length and a 15.6-inch collapsed length.

The monotube design separates the oil from the nitrogen gas charge with an internal floating piston, which Pro Comp says prevents cavitation. The shock uses vehicle-specific valving, so the damping is set for the CJ rather than a generic application, and the 2.0-inch body holds more oil to manage heat during extended off-road use.

The PR2087 is a rear shock with loop eyes at both the upper and lower mounts. Its 14mm chrome hardened shaft and silver powder-coated body are the same construction as the rest of the PRO-M line, and the shock is nitrogen charged for steadier damping under hard use.

Key features

  • Monotube body with an internal floating piston
  • Vehicle-specific valving on a multi-stage disc pack
  • 2.0-inch shock body with increased oil capacity
  • Redesigned wiper seal
  • 14mm chrome hardened shaft
  • Silver powder-coated finish

Shocks for older CJ builds

Older CJ frames were built around leaf springs and a solid axle, so rear shocks on these vehicles work hard at the mounts. A shock that is too long or too short for the installed lift will bottom out or run out of stroke, and either problem puts load on the eyes and the body. Measure the ride height with the truck on level ground before choosing a length.

Many CJ owners replace the shocks along with bushings and spring hangers, since worn hangers let the axle shift and wear the new shock early. Keep the shaft clean and check the boot after trail runs, because grit on the shaft works past the wiper seal over time.

  • Check spring hangers and bushings with the old shock off
  • Keep the shaft clean after dusty trail runs
  • Confirm lift height before choosing a length

Specifications

Brand Pro Comp Suspension
Part number PR2087
Shock series PRO-M
Shock type Monotube, nitrogen gas charged
Position Rear
Extended length 24.3 in
Collapsed length 15.6 in
Shock body diameter 2.0 in
Shaft 14mm chrome hardened
Upper mount Loop
Lower mount Loop
Finish Silver powder coat
Lift height Models with a 3 to 4 inch lift
Boot Polyurethane, included

Vehicle fitment

It fits the 1960–1983 Jeep CJ5 in the Base, Golden Eagle, Laredo, Limited and Renegade trims, and the 1976–1986 Jeep CJ7 in the Base, Golden Eagle, Golden Hawk, Laredo, Limited and Renegade trims.

Wrangler models, including the YJ, are not on this list. Confirm your vehicle’s year, model and trim before ordering.

Installation notes

Compare the 24.3-inch extended and 15.6-inch collapsed lengths with your installed lift before fitting. Pro Comp rates the shock for a 3 to 4 inch lift, so a taller or shorter lift changes the stroke required and should be checked at full droop and full compression.

What’s included

One CJ rear shock, fitted with the polyurethane boot already on the shock. Check the package contents against your installation before starting.

Fitment

VehicleYearsTrims
Jeep CJ51960–1983Base, Golden Eagle, Laredo, Limited, Renegade
Jeep CJ71976–1986Base, Golden Eagle, Golden Hawk, Laredo, Limited, Renegade

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Does the PR2087 fit a 1976 to 1986 Jeep CJ7?

Yes. The listed fitment includes the 1976–1986 CJ7 in several trims, and the shock is designed for a 3 to 4 inch lift. Confirm your model year and trim before ordering.

Will the PR2087 fit a Jeep Wrangler YJ?

No. Wrangler models, including the YJ, do not fit this shock. It is for the CJ5 from 1960 to 1983 and the CJ7 from 1976 to 1986 only.

What are the extended and collapsed lengths of the PR2087?

The extended length is 24.3 inches and the collapsed length is 15.6 inches. Compare both figures with your installed lift before ordering.

What should I check before fitting a shock to an older CJ?

Confirm the installed lift and the axle position, then check the spring hangers and bushings. Measure the ride height at the shock mounts so you know the stroke the new shock must cover before final tightening.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon