Overview
The Poison Spyder 17-03-032-ALUM is an extra wide aluminum front crusher flare for the Jeep Wrangler JK in two-door and four-door models. It is 2-1/4 inches wider than standard width front flares. The flare replaces the thin plastic factory flares, which are among the most vulnerable body components on a Jeep on the trail.
The aluminum version weighs 11.8 lbs per flare, while a steel JK front crusher flare weighs 31.6 lbs without hardware. Aluminum may suit owners who want to save weight, including to improve fuel mileage or gain an advantage off-road. It cannot withstand the same direct impacts as steel, so the driver has to be more careful when wheeling with aluminum flares.
The flare is built on a CNC laser cut 3/16-inch mounting plate, brake-formed to fit the subtle curves of the JK body panels. The top plate is 1/8-inch aluminum, hand formed around the flare to follow the JK’s body lines. The outer tube is thicker walled than the steel version, which recovers some of the strength lost by switching to aluminum.
Each set includes an inner brace set that ties the flare into the heavier steel of the JK inner body tub. The braces bypass the thin outer sheet metal, so impacts are carried by the inner structure.
Rubber liners are included to sit between the flare and the body. They protect the paint where the flare contacts the Jeep, even out the contact area and help keep moisture, dirt and debris from collecting. The liners are cut from premium EPDM rubber. The kit also has mounting provisions to replace the factory side marker with a 3/4-inch round LED marker light, which is sold separately. Poison Spyder also makes the steel version of these flares under a separate listing.
Key features
- Extra wide front flare, 2-1/4 inches wider than standard width
- Aluminum construction, 11.8 lbs per flare
- CNC laser cut 3/16-inch mounting plate with a 1/8-inch aluminum top plate
- Inner brace set that transfers impacts to the inner tub
- EPDM rubber liners for paint protection
- Mounting provision for a 3/4-inch round LED marker, sold separately
Front flare fit and weight
The front flare sits near the steering components, so fitment checks start with the wheel turning both ways. With the tire fitted, confirm there is room for the tire at full lock and that the flare does not contact the fender or the steering linkage. The factory wheel well liner and any trimmed sections should be checked for clearance.
Weight matters at the front, so a lighter flare can reduce the load on the front end. The trade-off is that aluminum is less forgiving of direct hits. Watch for bent edges and any change in the mounting plate after rocky sections. Replace worn rubber liners if they start to compress or tear, because the liners cushion the paint at the contact point.
- Check steering clearance at full lock
- Inspect the liners for compression or tears
- Watch for bent edges after rocky runs
- Keep mounting hardware tight
Specifications
| Brand | Poison Spyder Customs |
|---|---|
| Part number | 17-03-032-ALUM |
| UPC | 614901750645 |
| Location | Front |
| Type | Tube fender |
| Width | Extra wide, 2-1/4 inches wider than standard |
| Material | Aluminum |
| Weight | 11.8 lbs per flare (steel version 31.6 lbs, not including hardware) |
| Mounting plate | 3/16-inch |
| Top plate | 1/8-inch aluminum |
| Installation type | Cutting or drilling required |
| Fitment type | Direct fit |
Vehicle fitment
These aluminum front crusher flares are made for the Jeep Wrangler JK, which covers the 2007–2018 model years in two-door and four-door bodies.
Only the JK is named for these front flares, so TJ, LJ and JL are not covered. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
Installation requires cutting or drilling. Keep the factory wheel well liner if you want the inner braces hidden, and plan for trimming the plastic wheel well, which the kit’s hardware and brackets are intended to reinstall.
What’s included
The aluminum front flare with its mounting plate, top plate, inner brace set and EPDM rubber liners, plus the hardware and mounting brackets for the trimmed wheel well.
Not included: the 3/4-inch round LED marker light, which is sold separately.























