Overview
The Omix-ADA 18670.35 is a Dana 30 outer axle snap ring, offered as a direct OE replacement for classic Jeep models from the 1940s through the early 1970s. A snap ring is a spring-steel clip that seats in a groove to hold a component in place, and this one belongs at the outer end of a Dana 30 axle.
It is built to original specifications and carries a limited five year warranty from Omix-ADA. The fit covers Willys military and civilian models, CJs, Jeepsters, Wagoneers and J-series trucks, with years set for each model.
Nothing else is stated about the ring, such as its diameter or thickness, so the Dana 30 designation and the vehicle list are the identifiers to use.
Key features
- Dana 30 outer axle snap ring
- Direct OE replacement to original specifications.
- Limited five year manufacturers warranty from Omix-ADA
- Direct fit for the listed models
- Covers more than thirty classic Jeep model lines
Care and inspection
A snap ring that holds an axle component in place is a small part that does a big job. When it is removed, it can be distorted, so a new ring is a sensible choice whenever the old one is bent, flat or has lost its tension. Work with the correct snap ring pliers and keep the groove clean before seating the new ring.
Axle ends take heavy loads from the wheel and the terrain, so the snap ring should be checked whenever the axle is opened. Look for a ring that sits loosely in its groove, rust or cracks, and grease or dirt that hides wear. Because the ring is one part of a larger assembly, inspect the seals and bearing surfaces it works with at the same time.
- Replace a ring that is bent or has lost tension
- Clean the groove before fitting the new ring
- Check the seals and bearings during the same job
Specifications
| Brand | Omix-Ada |
|---|---|
| Part number | 18670.35 |
| UPC | 804314011307 |
| _pn | 18670.35 |
| Part type | Outer axle snap ring |
| Axle | Dana 30 |
| Fit type | Direct fit (Omix-ADA) |
| Warranty | Limited five year (Omix-ADA) |
Compare the ring’s size against the old one before installing.
Vehicle fitment
It covers the vehicles below, mostly built from the late 1950s to 1971, plus earlier Willys models. Vehicles outside the listed years and models fall outside this fit, especially the Wrangler (YJ, TJ, JK) and CJ7.
The manufacturer fitment list for part 18670.35 covers: 1959–1960, 1966 Jeep CJ3; 1959–1960, 1966–1971 Jeep CJ5; 1959–1960, 1966–1971 Jeep CJ6; 1966–1967, 1973 Jeep Commando; 1961–1967 Jeep Dispatcher; 1959–1960 Jeep DJ3; 1966–1968 Jeep DJ6; 1957–1958 Jeep F4; 1958–1966 Jeep FC150; 1963–1966 Jeep FC170; 1963–1966 Jeep FC170HD; 1963–1967 Jeep Gladiator; 1963–1971 Jeep J-100; 1965–1971 Jeep J-2500; 1968–1970 Jeep J-2600; 1968–1970 Jeep J-2700; 1968 Jeep J-2800; 1968–1970 Jeep J-3500; 1968–1970 Jeep J-3600; 1968–1970 Jeep J-3700; 1968–1970 Jeep J-3800; 1971 Jeep J-4800; 1966–1971 Jeep Jeepster; 1962 Jeep Tornado; 1966–1967 Jeep Universal; 1961–1962 Jeep Utility; 1963–1967, 1971 Jeep Wagoneer (SJ); 1947–1955 Jeep Willys 1-Ton; 1946–1949 Jeep Willys CJ-2; 1949–1958 Jeep Willys CJ-3; 1955–1958 Jeep Willys CJ-5; 1956–1958 Jeep Willys CJ-6; 1956–1958 Jeep Willys DJ-3; 1949–1952 Jeep Willys Jeepster; 1946–1950 Jeep Willys Panel; 1951–1955 Jeep Willys Sedan Delivery; 1941–1942 Willys MB.
Not listed: the Wrangler (YJ, TJ, JK), the CJ7, and modern Jeep models, and any year outside the ranges given for each model. Confirm your vehicle’s year, model and trim before ordering.
What’s included
- Dana 30 outer axle snap ring, 18670.35









