Select your vehicle
-13%

Bilstein 5100 Series Shock Absorber – 24-186971

Bilstein

Shop Bilstein Shock Absorbers on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Bilstein 5100 Series rear shock absorber, part number 24-186971
  • Direct fit for the rear position with a 0 to 1 in. lift
  • Collapsed length 15.33 in., extended length 24.8 in., travel 9.47 in.
  • Stem upper mount, 12.4mm eye lower mount, 14mm shaft
  • Gas charged monotube design with boot included

Description

Overview

The Bilstein 5100 Series rear shock absorber, part number 24-186971, is a gas charged monotube design for lifted trucks, Jeeps and prerunners running a 0 to 1 in. lift. It has a single-tube body built for steady damping over a long service life. Confirm the application for your vehicle before ordering.

The 5100 Series uses a 46mm ID smooth body without coilover spring seats, so this is a standalone shock rather than a coilover. Its upper mount is a stem and its lower mount is a 12.4mm eye. Bilstein designed the line for specific manufacturer lift kits that keep the stock O.E.M. mounting configuration, and the attributes mark it as a direct-fit replacement for the rear position.

Key features

  • Gas charged monotube construction
  • Self-adjusting deflecting disc valving
  • High-flow piston that Bilstein says reduces harshness
  • Independent rebound and compression tuning
  • Larger working piston area for damping control
  • Designed for control with large diameter tires.
  • Boot included

Lift height and shock travel

Travel length describes how far the shock can extend and compress between its collapsed and extended positions. On a lifted vehicle, the usable travel is what keeps the wheel following the ground, so a shock that runs out of extension can bottom or lose control on the way down a rough grade. Matching the shock’s length to your ride height matters as much as the damping rate.

Lift kits often change the angles of the control arms and driveline, so check that bump stops and brake lines still clear after a shock swap. Rear shocks on lifted trucks work hard under load, which makes the mounts, bushings and hardware wear sooner than on stock vehicles. Replace worn hardware at the same time as the shock to keep the geometry true.

  • Measure the installed length before buying
  • Check bump stops for cracks
  • Inspect eye and stem bushings for play
  • Retighten mounts after the first trail runs

Specifications

Brand Bilstein
Part number 24-186971
UPC 4025258592844
Series 5100 Series
Position Rear
Fitment type Direct fit
Lift height 0 to 1 in. lift
Collapsed length 15.33 in.
Extended length 24.8 in.
Travel length 9.47 in.
Lower mount Eye, 12.4mm
Upper mount Stem
Shaft diameter 14mm
Body design 46mm ID smooth body (non-coilover)
Internal design Monotube
Hydraulic / gas charged Gas charged
Reservoir No
Finish Zinc plated
Boot Included

Vehicle fitment

It is a direct fit replacement for the rear position with a 0 to 1 in. lift. Confirm fit for your vehicle’s year, make, model and suspension height before ordering.

This part is for the rear position only. Confirm fit for your vehicle’s year, model and trim before ordering.

Installation notes

Keep the boot intact during installation, since it covers the shaft. Gas charged shocks are pressurized, so keep the body away from heat and do not puncture or open it.

What’s included

A boot is included. Check the package contents against your installation before starting.

SKU: BIL24-186971 Category:

Specification

Shipping weight 5.45 lbs
Package dimensions 26.80 × 3.00 × 3.00 in
brands

Questions & Answers

Is Bilstein part 24-186971 a front or rear shock?

It is a rear shock. Part 24-186971 is designed for the rear position, so it is not a front shock. It is a direct fit design for a 0 to 1 in. lift range.

What vehicles does Bilstein 24-186971 fit?

It is designed for lifted trucks, Jeeps and prerunners with a 0 to 1 in. lift. Bilstein built it to suit certain lift kits that keep the stock O.E.M. mounting configuration. Check fit against your vehicle's year, make, model and trim before buying.

What are the collapsed and extended lengths of this shock?

The collapsed length is 15.33 in. and the extended length is 24.8 in., with a travel length of 9.47 in. The lower mount is a 12.4mm eye, the upper mount is a stem, and the shaft diameter is 14mm.

Does the Bilstein 24-186971 come with a boot?

Yes. A boot is included to cover the shaft. Check the package contents on arrival and compare them with your installation before starting, including any mounting hardware you need.

How do I keep a lift-height rear shock working well?

Keep the boot intact, check the mounts after every few trail runs and avoid heat exposure to the body. Recheck bump stop clearance after any suspension change, since a shock can bottom out if its travel is used up.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Bilstein Shock Absorbers on Amazon