Manual Transmission Parts
Manual transmission parts cover the internal and external components that keep a manual gearbox shifting smoothly, from synchronizer key plates and blocking rings to seals, gaskets and shift boots. The group lists parts for transmissions such as the AX4, AX15 and T4/T5, with Crown Automotive, Omix-Ada, Jeep and Drake as the main brands. Compare part numbers on each product page, then compare the listings below.

A stick-shift Jeep can run for decades if the gearbox gets the small parts it needs. Here you'll find the synchro, bearing, seal and shifter pieces for manual transmissions from the Willys-era T90 to the AX15 and NV3550, so you can fix a grind, a leak or a sloppy shifter without replacing the whole unit.
Shifter parts are the largest group: knobs, boots, boot rings, bezels, bushings and levers. Internal parts come next, sorted by job: synchro rings, key plates, springs and hubs; bearings, seals and gaskets; shift forks, rails, detent balls and reverse gear parts. Every piece is listed by transmission model, and many also by gear position, so match both before you order.
Shop manual transmission parts by type
More part types (51)
- Manual Trans Bearing Retainer 2
- Manual Trans Cluster Gear 1
- Manual Trans Cluster Gear Bearing/Bushing 3
- Manual Trans Detent Ball 1
- Manual Trans Detent Spring 2
- Manual Trans Drain Plug 2
- Manual Trans First Gear Thrust Washer 1
- Manual Trans Input Shaft Seal Retainer 1
- Manual Trans Input Shaft Snap Ring Set 1
- Manual Trans Main Drive Gears 1
- Manual Trans Mainshaft Bearing 2
- Manual Trans Mainshaft Nut 1
- Manual Trans Mainshaft Spacer 1
- Manual Trans Mainshaft Washer 1
- Manual Trans Oil Filler Tube 1
- Manual Trans Output Shaft Seal 2
- Manual Trans Output Shaft Seal Retainer 1
- Manual Trans Reverse Gear 2
- Manual Trans Reverse Gear Pin 1
- Manual Trans Reverse Idler Plate 2
- Manual Trans Reverse Shift Head 1
- Manual Trans Shift Boot Ring 3
- Manual Trans Shift Bushing Kit 1
- Manual Trans Shifter Assembly 1
- Manual Trans Shifter Cover Seal 2
- Manual Trans Shifter Housing Bolt 1
- Manual Trans Shift Fork 1
- Manual Trans Shift Fork Clip 1
- Manual Trans Shift Fork Insert 2
- Manual Trans Shift Fork Roller 1
- Manual Trans Shift Handle Insulator 1
- Manual Trans Shift Lever Extension 1
- Manual Trans Shift Lever Kit 3
- Manual Trans Shift Lock Clip 1
- Manual Trans Shift Rail 1
- Manual Trans Shift Rail Plate 2
- Manual Trans Shift Rail Poppet Ball 2
- Manual Trans Shift Rod Clip 1
- Manual Trans Shift Rod Plastic Bushing 1
- Manual Trans Shift Rod Poppet Spring 1
- Manual Trans Shift Shaft Pin 1
- Manual Trans Synchro Assembly 1
- Manual Trans Synchro Hub 1
- Manual Trans Synchro Hub Assembly 1
- Manual Trans Synchro Key 1
- Manual Trans Synchronizer Assy Repair Kit 1
- Manual Trans Synchro Sleeve 1
- Manual Trans Top Gasket 3
- Neutral Safety Switch 1
- Shift Mode Synchronizer Blocking Ring 1
- T-90 Tranny Kit 1
Popular manual transmission parts
-
Manual Trans Shift Bezel
Rugged Ridge Manual Transmission Shifter Bezel – 11422.12
- Rugged Ridge manual transmission shifter bezel in CNC machined billet aluminum
- Fits 2007–2010 Jeep Wrangler (JK) models, 2-door and 4-door
- Replaces factory components with no drilling or modification
- Part number 11422.12, UPC 804314237837
SKU: RUG11422.12 -
Manual Trans Input Shaft Bearing
Crown Automotive AX15 Main Drive Gear Bearing – 83506074
- Crown Automotive AX15 main drive gear bearing, part 83506074
- Front position, direct fit replacement
- Fitment list: 1989 to 1999 Cherokee XJ, 1993 Grand Cherokee ZJ, 1997 Wrangler TJ Sport, 1988 to 1995 Wrangler YJ
- UPC 848399026658
SKU: CRO83506074 -
-
Manual Trans Input Shaft Seal
Crown Automotive NV3550 Main Drive Gear Seal – 4741296
- Crown Automotive NV3550 main drive gear seal, part 4741296
- Direct fit replacement for NV3550 transmissions
- Fitment list: 2000 to 2001 Cherokee XJ, 2002 to 2004 Liberty KJ, 2000 to 2004 Wrangler TJ
- UPC 848399007459
SKU: CRO4741296 -
-
Manual Trans Synchro Key Plate
Crown Automotive T15 Synchronizer Plate – J3192412
- Synchronizer plate for T15 manual transmissions, part number J3192412
- Fits 1967–1975 Jeep CJ5, CJ6 and Commando models
- Also fits 1971–1975 Jeep Wagoneer (SJ) and J-series trucks
- UPC 848399058765, direct fit listing
SKU: CROJ3192412 -
Manual transmission identification reference
The manual transmissions named in this category, with their gear count and the Jeeps they are best known in. Confirm yours by the case tag before ordering.
Transmissions in these listings
| T90 | 3-speed; Willys and early CJ |
|---|---|
| T14 / T150 | 3-speed; CJ |
| T18 | 4-speed; CJ and J-series trucks |
| T176 / T177 | 4-speed; early-1980s CJ |
| SR4 | 4-speed; early-1980s CJ |
| T4 / T5 | 4- and 5-speed; 1980s CJ |
| AX4 / AX5 | Aisin 4- and 5-speed; four-cylinder YJ and XJ |
| BA 10/5 | 5-speed; late-1980s XJ and MJ |
| AX15 | Aisin 5-speed; 4.0L six-cylinder YJ, XJ, TJ |
| NV3550 | 5-speed; replaced the AX15 in TJ and XJ |
| 6-speed | 2005–06 TJ/LJ (knob and pattern insert) |
Synchro and shift parts explained
| Blocking (synchro) ring | Brass cone that matches gear and shaft speed |
|---|---|
| Synchro key / key plate | Pushes the ring into the gear cone |
| Synchro spring | Holds the keys out against the sleeve |
| Synchro hub and sleeve | Hub rides the shaft; sleeve locks in the gear |
| Shift fork insert | Wear pad between the fork and the sleeve |
| Detent ball and spring | Hold the shift rail in gear or neutral |
| Cluster gear | Countershaft gear that drives the main gears |
Details stated on listings
| AX15 3rd/4th/5th synchro ring | Brass, 3 notches, 33 teeth, after serial 00705124 |
|---|---|
| T90 blocking ring | 2 required |
| AX15 input shaft snap ring | 2.15 mm x 37.50 mm inner diameter |
| T170 shift lever | 19-1/2" from top to pivot |
| AX4/AX5/AX15 rear adapter seal | One seal fits all three |
| NV3550 cluster gear bearing | Same part front or rear |
Many internal parts changed during a production run, such as the AX15 synchro ring at a serial number break. Check the case tag and serial number against the listing before ordering.
All Manual Transmission Parts 198 parts
-
Manual Trans Shift Lever Kit
Skyjacker Rock Ready Shifter Bracket – JSRB231A
- Skyjacker Rock Ready shifter bracket relocates the 4WD shifter for transfer case drops
- Part number JSRB231A
- One-piece steel spacer, 1 inch lift height, welding required
- Works with manual or automatic transmissions; AX15 needs modification
SKU: SKYJSRB231A -
-
-
-
-
Shift Mode Synchronizer Assembly
Crown Automotive NP231 Shift Mode Synchronizer – 4796967
- Pre-assembled shift mode synchronizer for the NP231 transfer case
- Includes center hub, outer sliding hub, spring clips and synchronizer plates
- Factory style replacement
- Fits 1987–1995 Cherokee XJ and Wrangler YJ
- Part number 4796967
SKU: CRO4796967 -
-
Manual Trans Shift Bezel
Rugged Ridge Manual Transmission Shifter Bezel – 11422.12
- Rugged Ridge manual transmission shifter bezel in CNC machined billet aluminum
- Fits 2007–2010 Jeep Wrangler (JK) models, 2-door and 4-door
- Replaces factory components with no drilling or modification
- Part number 11422.12, UPC 804314237837
SKU: RUG11422.12 -
-
What these parts do
A manual transmission uses gears on shafts, with synchronizers that match speeds so gears engage without grinding. Over many miles, the synchro rings, key plates, springs, bearings and seals wear, and the shifter parts loosen. This category covers both internal rebuild parts and external items. Subcategories include synchro key plates, blocking rings, synchro springs, input shaft seals, gaskets, shift knobs, shift boots and label patterns.
Identify the transmission first
Rebuild parts are specific to the transmission model, and titles here reference units like the AX4, AX15 and T4/T5. Identify yours by the tag on the case, the casting numbers, the number of bolts on the cover and the vehicle's engine and drivetrain, and then match the part to it. Parts for different gear positions, such as first-second and third-fourth, are not the same, and manufacturers label them accordingly.
Parts you might need
- Synchronizer rings and key plates: worn rings cause grinding when shifting into a particular gear.
- Bearings and seals: an input shaft seal or front bearing retainer seal stops leaks at the bellhousing, and the bearings handle shaft loads.
- Gaskets and hardware: replace these any time the case or cover is opened.
- Shift forks and inserts: worn inserts cause sloppy gear selection.
- Shift knobs, boots and patterns: a cosmetic and comfort refresh that is easy to install.
Rebuild or replace
A transmission rebuild needs a clean workspace, bearing and snap ring pliers, a press for some work and the factory service manual for clearances and torque values. Replace parts as a set rather than one at a time, since a worn gear will quickly damage a new synchro. Some owners prefer a complete rebuilt unit to the labor, and a transmission shop can perform the work if you are not comfortable with it.
Fluid and compatibility
Use the fluid type and fill level that the manufacturer specifies, since some manual transmissions require ATF or special gear oil. Confirm fitment for your exact year, make, model and transmission, and compare part numbers with the manufacturer's specifications before choosing. Replace the clutch hydraulics and pilot bearing if the transmission is already out.
Diagnosis comes before parts. Before opening a transmission, check the simple items. Low or wrong fluid, a clutch that does not fully release, worn shifter bushings and a loose shift linkage all cause symptoms that resemble internal failure. Shift the transmission with the engine off to see whether the gears select cleanly, which separates a clutch problem from a gearbox problem. Noises that change with clutch pedal position point to the clutch or input bearing, while noises that change with gear point to the gear set.
If you do open it, keep everything in order. Photograph each step, bag and label small parts, and clean the case and magnet thoroughly. Inspect gear teeth, shafts and bearing races for chips, pitting and discoloration, and replace anything doubtful. Use the proper assembly lubricant on synchros and bearings, and set endplay and preload where the manual calls for it. After reassembly, fill with the specified fluid, check for leaks and take a careful test drive, shifting through every gear. Parts such as shift knobs and boots are easy upgrades that do not require any teardown.
Popular Manual Transmission Parts brands
- Crown Automotive (106)
- Omix-Ada (55)
- Jeep (16)
- Drake (11)
- Rugged Ridge (6)
- B&M (5)
- Rampage (2)
- Mr. Gasket Company (2)
- RT Off-Road (1)
- Trail Gear (1)
- Energy Suspension (1)
- Skyjacker (1)
Manual Transmission Parts FAQ
How do I know which manual transmission I have?
Look for a tag or casting numbers on the case, count the bolts, and check your vehicle's engine and year in the service manual. Titles like AX4, AX15 and T5 name common units. Verify with the manufacturer's data.
What causes grinding when shifting into a gear?
Worn synchronizer rings or key plates are a common cause, but low or wrong fluid, clutch release problems and linkage issues can also grind. Diagnose the clutch and fluid first, then the synchros.
Should I replace seals when the transmission is out?
Yes. Seals and gaskets are cheap relative to the labor of removing the transmission again. Replace the input shaft seal, bearing retainer seal and cover gaskets while it is apart.
Can I rebuild a manual transmission myself?
Experienced home mechanics do, using a service manual and the right tools. It needs careful measuring and clean work. If unsure, a transmission shop or a rebuilt unit may be a better choice.


































