Select your vehicle

Jeep NSG370 Input Shaft Needle Bearing – 05096465AA

Jeep

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Factory replacement input shaft needle bearing for the Jeep NSG370
  • Part number JEP05096465AA
  • Fits 2007–2018 Jeep Wrangler JK models
  • Factory replacement part, direct fit

Description

Overview

The Jeep NSG370 input shaft needle bearing, part JEP05096465AA, is a factory replacement bearing for the NSG370 input shaft. It fits 2007–2018 Jeep Wrangler JK models, in both two-door and four-door body styles.

The needle bearing supports the input shaft so it turns freely inside the transmission. The factory part is the direct-fit replacement when that bearing needs renewing.

Key features

  • Factory replacement part from Jeep
  • Direct fit for the NSG370 input shaft
  • Identified by Jeep part number JEP05096465AA

Before you replace the bearing

A worn input shaft needle bearing often shows up as noise or a rough feel from the transmission, especially when the clutch is engaged and the input shaft is spinning. Before fitting a new bearing, check the input shaft tip and the seat in the case for scoring, heat marks or play. A bearing seated on a damaged shaft or bore can wear out quickly, so cleaning and inspecting those surfaces is worth the time while the transmission is out.

Because the bearing sits at the transmission input, related seals and clutch components are often inspected at the same time. Use fresh transmission fluid of the type the NSG370 requires when reassembling. Keep the new bearing clean and dry until it is installed, and press it straight into place rather than hammering it in.

Specifications

Brand Jeep
Part number JEP05096465AA
Component Input shaft needle bearing
Transmission NSG370

Vehicle fitment

It fits 2007–2018 Wrangler (JK) models, both two-door and four-door.

Wranglers from 2018 on, such as the JL, are not covered by this list. Confirm your vehicle’s year, model and trim before ordering.

Installation notes

The input shaft bearing is replaced with the transmission out of the vehicle. Inspect the input shaft and its seat for wear before fitting the new needle bearing.

What’s included

One input shaft needle bearing.

Fitment

VehicleYearsTrims
Jeep Wrangler (JK)2007–201870th Anniversary (2-Door), 75th Anniversary (2-Door), Rubicon (2-Door), Sahara (2-Door), Sport (2-Door), Sport S (2-Door), Unlimited 70th Anniversary (4-Door), Unlimited 75th Anniversary (4-Door), Unlimited Rubicon (4-Door), Unlimited Sahara (4-Door), Unlimited Sport (4-Door), Unlimited Sport S (4-Door), Unlimited X (4-Door), X (2-Door)

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Does this NSG370 needle bearing fit a 2007–2018 Jeep Wrangler JK?

Yes. It fits 2007–2018 Wrangler JK models, both two-door and four-door, as a factory replacement for the NSG370 input shaft bearing.

What transmission is this bearing for?

It is the input shaft needle bearing for the NSG370 transmission, part number JEP05096465AA, and it matches the Wrangler JK fitment.

Is this a genuine Jeep part?

Yes. It is a factory replacement part with Jeep part number JEP05096465AA and a direct fit for the years shown.

Does the 2018 and newer Wrangler use this bearing?

Its fit covers 2007–2018 Wrangler JK models. If you drive a 2018 or newer Wrangler, verify that the year, model and trim match before you order.

How can I tell if the input shaft bearing is worn?

Common signs include noise from the transmission area, a rough shifting feel, or a whine that changes with engine speed. Inspect the input shaft tip and bearing seat when the transmission is out, and replace the bearing if the surfaces are scored or the bearing feels rough when turned.

Should the pilot bushing be replaced at the same time?

Often it is a good idea to inspect the pilot bushing when the input shaft bearing is replaced, since both support the input shaft. Check for wear, a loose fit or damage, and replace it if the bore feels worn. This helps keep clutch alignment solid after reassembly.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon