Select your vehicle

Omix-ADA Rear Drive Shaft – 16591.26

Omix-Ada

Shop Jeep Wrangler TJ Drive Shafts on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Rear drive shaft for 2.4L four-cylinder with a manual transmission
  • Built for the Dana 35 rear axle
  • Same size as the factory original
  • Omix-Ada part number 16591.26

Description

Overview

The Omix-Ada 16591.26 is a rear drive shaft for 2.4L four-cylinder Jeeps with a manual transmission and a Dana 35 rear axle. It fits the 2003–2006 Jeep Wrangler (TJ) SE.

The shaft matches the factory original size for this application and is a direct OE replacement built to original specifications.

Key features

  • Rear drive shaft for the 2.4L four-cylinder
  • Built for a manual transmission
  • Same size as the factory original for the application
  • Designed for the Dana 35 rear axle
  • No slip yoke eliminator required

Checking the driveline

A rear drive shaft carries engine torque from the transmission to the rear axle, and it moves up and down with the suspension as the Jeep flexes over uneven ground. The joints at each end allow that movement, so wear in them shows up first as vibration, clunking or a shudder when the vehicle starts to move.

Because this shaft has non-CV joints, operating angle matters. Lift height and pinion angle changes affect how hard the joints work, so a shaft replaced alongside a suspension change should be checked for vibration on the road before long trips off-road.

  • Look for play in the u-joint bearing caps
  • Check for grease seeping from the joints
  • Inspect the flange bolts for tightness
  • Watch for vibration that changes with speed

Specifications

Brand Omix-Ada
Part number 16591.26
UPC 804314140304
Length Stock
Engine 2.4L four-cylinder
Transmission Manual
Axle Dana 35 rear
Joint type Non-CV
Position Rear
Slip yoke eliminator Not required
Fitment type Direct fit

Vehicle fitment

It fits the 2003–2006 Jeep Wrangler (TJ) SE.

The list does not include the TJ Sport, Sahara or Rubicon, or the Wrangler LJ. Confirm your vehicle’s year, model and trim before ordering.

What’s included

One rear drive shaft. Mounting hardware is not included.

SKU: OAI16591.26 Category:

Specification

Shipping weight 20.00 lbs
Package dimensions 16.00 × 6.00 × 6.00 in
brands

Fitment

VehicleYearsTrims
Jeep Wrangler (TJ)2003–2006SE

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Will the Omix-Ada 16591.26 fit a 2004 Jeep Wrangler TJ SE?

Yes. It fits the 2003–2006 Jeep Wrangler (TJ) SE, which covers 2004. Confirm the engine is the 2.4L four-cylinder with a manual transmission before ordering.

Does it fit a Dana 35 rear axle?

Yes. It is built for the Dana 35 rear axle and matches the factory original size. Check the axle before ordering.

Is this a front driveshaft?

No. The position is rear. The specifications say the shaft does not require a slip yoke eliminator, and it is a direct OE replacement built to the original specifications.

What signs point to a worn rear drive shaft?

Vibration that rises with speed, clunking when shifting between drive and reverse, and grease seeping from a joint are the usual signs. Check the joints for play and the bolts at each flange before replacing the shaft.

Should the u-joints be inspected when the shaft is replaced?

Yes. Checking the joints and flange hardware during the same job helps prevent a repeat repair. Tighten each flange bolt to the vehicle's specification after installation.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Jeep Wrangler TJ Drive Shafts on Amazon