Select your vehicle

Omix-ADA Rear Drive Shaft – 16591.04

Omix-Ada

Shop Jeep CJ7 Drive Shafts on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Rear drive shaft for manual T4, T5 or T170 transmissions
  • Collapsed length of 23 inches
  • Fits 1981–1986 Jeep CJ7
  • Omix-Ada part number 16591.04

Description

Overview

It is a stock-length rear drive shaft for Jeep CJ7 models with a manual T4, T5 or T170 transmission. It fits the 1981–1986 Jeep CJ7 in the Base, Laredo, Limited and Renegade trims. It is a direct-fit replacement in the rear position.

The shaft has a collapsed length of 23 inches and is built to the original specifications. It is a direct-fit replacement in the rear position.

Key features

  • Rear drive shaft at stock length
  • Built for manual T4, T5 and T170 transmissions
  • Collapsed length of 23 inches
  • No slip yoke eliminator required

Driveline angles and wear

A rear drive shaft transfers engine power to the axle through universal joints that flex as the suspension moves. Its length and angle must suit the transmission and axle positions, so a shaft that is too long or bent can cause vibration and joint wear. Keeping the joints greased and the shaft balanced helps it run smoothly on the road.

Stock-length shafts are the usual choice for an unmodified suspension, because the joint angles stay within what the design expects. Any suspension change, such as a different lift or axle position, can change those angles and call for a closer look at the driveline. Inspect the shaft after rough trails or any hard impact, since a small dent can unbalance it.

  • Check the universal joints for play and dry bearings
  • Inspect the yokes and slip splines for wear
  • Look for missing or loose balance weights
  • Check the shaft and mounting points after off-road use

Specifications

Brand Omix-Ada
Part number 16591.04
UPC 804314036447
Length Stock
Collapsed length 23 inches
Transmission Manual T4, T5 or T170
Joint type Non-CV
Position Rear
Slip yoke eliminator Not required
Fitment type Direct fit

Vehicle fitment

It fits the 1981–1986 Jeep CJ7 (Base, Laredo, Limited and Renegade).

The list does not include the CJ5, the Scrambler or the Wrangler YJ. Confirm your vehicle’s year, model and trim before ordering.

What’s included

One rear drive shaft. Check the package contents against your installation, including any mounting hardware you need, before starting.

SKU: OAI16591.04 Category:

Specification

Shipping weight 13.00 lbs
Package dimensions 32.00 × 6.00 × 5.00 in
brands

Fitment

VehicleYearsTrims
Jeep CJ71981–1986Base, Laredo, Limited, Renegade

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Will the Omix-Ada 16591.04 fit a 1984 Jeep CJ7?

Yes. It fits the 1981–1986 Jeep CJ7, which covers 1984, in the Base, Laredo, Limited and Renegade trims. It is built for manual T4, T5 or T170 transmissions, so confirm the transmission before ordering.

Does this shaft need a slip yoke eliminator?

No. The specifications say it does not require one. The shaft has a collapsed length of 23 inches and a stock length, and it is a rear drive shaft.

Is this a front driveshaft?

No. It is a rear drive shaft, so it does not fit the front position. It has a stock length and a non-CV joint design, and it is sold as a direct-fit replacement.

What signs show a driveshaft needs replacing?

Common signs include vibration that grows with road speed, clunks when shifting between drive and reverse, and a dented or bent shaft. Worn universal joints also show play when the shaft is turned by hand. Inspect the joints and balance before deciding a new shaft is needed.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Jeep CJ7 Drive Shafts on Amazon