Select your vehicle

Omix-ADA Ball Joint – 18037.04

Omix-Ada

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Rear upper ball joint
  • Fits 1999–2004 Jeep Grand Cherokee (WJ)
  • Not lubeable, part number 18037.04, UPC 804314138523

Description

Overview

The Omix-ADA 18037.04 is a rear upper ball joint for the 1999–2004 Jeep Grand Cherokee (WJ). It is offered for the Laredo, Limited, Overland, Special Edition and Sport versions.

It is a direct OE replacement built to original specifications. The joint is not lubeable and has no grease fitting.

Key features

  • Rear upper position
  • Dana 30A axle type
  • Not lubeable, so there is no grease fitting to service
  • Direct OE replacement part

Before replacing a ball joint

A ball joint is a pivot that connects the steering knuckle to the control arm, allowing the wheel to steer and move up and down over bumps. On a solid axle like this one, the upper joint carries load as the axle articulates, so wear shows up as looseness, clunking over bumps, or uneven tire wear. Inspect for play at the stud, and look at the dust boot for tears that let road grit into the joint.

Because the joint is not lubeable, the usual approach is to replace it when wear appears rather than servicing it with grease. Lower joints and other suspension parts on the same side often wear together, so check them during the same job. Set alignment after any joint replacement so the steering geometry returns to its intended angles.

Specifications

Brand Omix-Ada
Part number 18037.04
UPC 804314138523
Position Rear upper
Axle location Front (as recorded)
Axle type Dana 30A
Lubeable No

Vehicle fitment

The joint fits the following vehicle:

  • 1999–2004 Jeep Grand Cherokee (WJ), in the Laredo, Limited, Overland, Special Edition and Sport versions

Other Grand Cherokee generations and Cherokee models are not on this list. Confirm your vehicle’s year, model and trim before ordering.

Installation notes

The position is rear upper, while the axle location is recorded as front. Compare the new joint with the old one, including its stud and mounting points, before you install it.

What’s included

Check the package contents against your installation before starting, including any hardware your joint needs.

SKU: OAI18037.04 Category:

Specification

Shipping weight 2.50 lbs
Package dimensions 5.50 × 4.50 × 4.30 in
brands

Fitment

VehicleYearsTrims
Jeep Grand Cherokee (WJ)1999–2004Laredo, Limited, Overland, Special Edition, Sport

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Does the Omix-ADA 18037.04 fit a 2002 Grand Cherokee?

Yes. It fits the 1999–2004 Jeep Grand Cherokee (WJ), so a 2002 model falls inside that range. Confirm the trim before ordering, since Laredo, Limited, Overland, Special Edition and Sport versions are covered.

Can the 18037.04 be greased?

No. The joint is not lubeable, so it has no grease fitting to service. Plan on replacing it at wear rather than relying on greasing.

Is the 18037.04 a front joint?

The position is rear upper, but the axle location is recorded as front. Because those two details do not match, compare the joint with the one you remove before installing it.

How can I tell if this ball joint needs replacing?

Look for play at the stud, clunking over bumps, a torn dust boot or uneven tire wear. Because the joint is not lubeable, replacing it once wear shows is the normal approach, and an alignment check should follow.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon