Select your vehicle

G2 Dana 44 Jeep Wagoneer Front Chromoly Axle Kit – 98-2033-004

G2 Axle and Gear

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Front Dana 44 chromoly axle kit for the Jeep Wagoneer, part number 98-2033-004
  • 30 splines, uses 5-760X joints
  • Fits 1974–1979 Jeep Wagoneer (SJ)
  • Differential not included

Description

Overview

The G2 98-2033-004 is a front Dana 44 chromoly axle kit for the Jeep Wagoneer. It fits 1974–1979 Wagoneer (SJ) models, including the 74–79 range.

Forged 4340 chrome-nickel alloy axles are built for off-road loads, oversized tires and the high torque of low-geared drivetrains. The yoke area around the U-joint cap has extra material to resist distortion. The kit has 30 splines, uses 5-760X joints, and does not include a differential.

Key features

  • Front Dana 44 axle kit for the Wagoneer
  • Forged 4340 chromoly alloy
  • Extra yoke material around the U-joint cap
  • 30-spline shafts
  • Uses 5-760X joints

Why Wagoneer axles wear

Full-size Wagoneers carry a lot of weight, and the front axle takes that load every time the truck turns, climbs or brakes. Axle shafts are the link between the differential and the hubs, so they see both steady torque and sudden shock from rocks and ruts. Stock shafts can twist or break under heavy use, especially after a larger tire has been added, which is why owners look at upgraded shafts.

Before choosing shafts, think about the whole front end. A shaft is only as good as its joint, and a worn U-joint can cause vibration and uneven wear inside the axle. Check the hub bearings, seals and the carrier’s condition at the same time. Old grease that has turned milky suggests water has entered the axle and the bearings should be inspected.

If the truck has a lift or a regear, the front axle works harder. Shaft torque goes up with lower gearing, so it helps to confirm the carrier and gearing are a matched set before installing. Keep the axle breather clear and check fluid levels after trail use.

Specifications

Brand G2 Axle and Gear
Part number 98-2033-004
UPC 631410097528
Axle type Dana 44
Axle location Front
Shaft position Front left
Spline count 30 splines
Joint 5-760X
Material 4340 chromoly alloy
Differential Not included

Vehicle fitment

It fits 1974–1979 Jeep Wagoneer (SJ) models, covering the 74–79 Wagoneer.

The 1980–1990 Wagoneer uses a different front kit, 98-2033-005. Confirm your vehicle’s year, model and trim before ordering.

Installation notes

The kit is supplied without a differential, so the front carrier needs to be a Dana 44 with 30 splines to match these axles.

What’s included

The front Dana 44 chromoly axle kit with 30-spline shafts.

Not included: Differential.

SKU: G/298-2033-004 Category:

Specification

Shipping weight 32.00 lbs
Package dimensions 37.00 × 7.50 × 7.30 in
brands

Fitment

VehicleYearsTrims
Jeep Wagoneer (SJ)1974–1979Base, Custom, Limited

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Will the G2 98-2033-004 fit a 1977 Jeep Wagoneer?

Yes. It fits 1974–1979 Wagoneer (SJ) models, and 1977 falls inside that range. The 74–79 Wagoneer years match this kit. Confirm fit for your vehicle's year, model and trim before ordering.

Is a differential included with this kit?

No. The differential is not included, so use a Dana 44 front carrier with 30 splines that matches these axles.

Which joint does the kit use?

It uses 5-760X joints with a 30-spline end. The axles are forged 4340 chrome-nickel alloy, built for off-road loads and the high torque of low-geared drivetrains.

Does this kit fit a 1985 Wagoneer?

No. The kit only fits 1974–1979 Wagoneer (SJ) models. The 1980–1990 Wagoneer uses the separate 98-2033-005 kit, so match your model year before ordering.

How can I tell when Wagoneer front axle shafts are worn?

Look for clicking on tight turns, vibration under acceleration, grease leaking from the joint boots and visible twisting or cracks. Any of these signs means the shaft or joint should be inspected and replaced before it fails on the trail.

Should U-joints be replaced with the shafts?

Often yes. A joint with play, binding or a torn cap will wear a new shaft quickly, so inspecting or replacing it during the same job saves a second tear-down. Clean the yoke surfaces and use fresh grease.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon