Select your vehicle

Crown Automotive Steering Tie Rod End – J0932191

Crown Automotive

Shop Jeep Wagoneer SJ CJ Steering on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Crown Automotive left steering tie rod end, part CROJ0932191
  • Left tie rod on tie rod tube, 3-7/8 inch long
  • Left hand threads
  • Fits 1963–1969 Jeep Gladiator and Wagoneer SJ

Description

Overview

The Crown Automotive left steering tie rod end, part number CROJ0932191, is a left tie rod end for the left tie rod on the tie rod tube. It has left hand threads and a stated length of 3-7/8 inch.

The fitment covers the 1963–1969 Jeep Gladiator Base and the 1963–1969 Jeep Wagoneer SJ Base. A tie rod end is the joint at the outer end of the steering linkage.

Key features

  • Left position on the tie rod tube
  • Left hand threads
  • 3-7/8 inch length.
  • Direct fit for the 1963–1969 Gladiator and Wagoneer SJ in Base trim.

Tie rods on older Jeep steering

A tie rod end is the joint that lets the steering arm pivot as the wheel turns. Older Jeep linkage uses these ends at the outer side of the tie rod, and a worn joint shows up as wander, a clunk over bumps or uneven front tire wear. Checking the joint for play by hand is a simple first step.

Matching the thread direction matters. Left and right ends are not interchangeable on the same tube, and the tube length sets toe. Keep the original length as a reference, count turns when unscrewing, and set toe with the wheels straight once the new end is on.

  • Note the thread direction before removing the old end
  • Count turns to keep the starting toe close
  • Replace the boot if it is split
  • Have toe set after the job

Specifications

Brand Crown Automotive
Part number CROJ0932191
Position Left
Length 3-7/8 inch
Thread Left hand threads
Fitment type Direct fit

Vehicle fitment

The manufacturer fitment list shows this tie rod end for the 1963–1969 Jeep Gladiator in Base trim and the 1963–1969 Jeep Wagoneer (SJ) in Base trim.

Not covered: Cherokee, Wrangler, Grand Cherokee and other Jeep models outside the list. Confirm your vehicle’s year, model and trim before ordering.

Installation notes

Left hand threads mean this end installs in the opposite direction from a right-hand tie rod end, so match the thread direction before fitting it. Have the front end aligned after installation.

What’s included

The left tie rod end is the only item supplied. Confirm whether jam nuts, boots or clamps are needed before starting.

SKU: CROJ0932191 Categories: , ,

Fitment

VehicleYearsTrims
Jeep Gladiator1963–1969Base
Jeep Wagoneer (SJ)1963–1969Base

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Is this tie rod end for the left or right side?

It is the left tie rod end, for the left tie rod on the tie rod tube, with left hand threads. Confirm which side you need before ordering.

What length is this tie rod end?

It is 3-7/8 inch long with left hand threads. Compare that length with the part you are replacing before installing it on the tie rod tube.

Which Jeep models does this tie rod end fit?

It fits the 1963–1969 Jeep Gladiator and 1963–1969 Wagoneer SJ, both in Base trim. Other models are not covered, so confirm your vehicle before ordering.

Does this tie rod end come with jam nuts?

Plan to reuse your existing nuts or buy them separately. The tie rod end itself has left hand threads, so match that direction.

Should a worn tie rod end be replaced in pairs?

Not always. Replace the joint that has play, but check the opposite end too, since it carries the same load. Mismatched ends can leave the steering feeling uneven.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Jeep Wagoneer SJ CJ Steering on Amazon