Select your vehicle

Camburg Performance Spindle Kit – CAM-110123

Camburg Engineering

Shop Ford F-150 Spindle on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Fabricated front spindles for 2009–2013 Ford F-150 trucks, part number CAMCAM-110123
  • Raises the front end 4.5 inches compared with stock.
  • Track width increased 1.25 inches per side
  • Gives 4.5 to 6.5 inches of lift when combined with a coilover
  • Bolts on with the hardware included, plus longer stainless braided front brake lines

Description

Overview

The Camburg CAMCAM-110123 is a fabricated front spindle kit for the 2009 to 2013 Ford F-150. The spindles lift the front end 4.5 inches compared with stock and widen the track by 1.25 inches per side.

The spindle supplies the lift, which gives more droop travel and a better ride than maxing out the coilovers. The spindles can give 4.5 to 6.5 inches of lift when combined with a coilover, and they add 4.5 inches of ground clearance. They are intended for 2WD F-150 trucks.

Key features

  • Fabricated spindles (knuckles), laser cut from CAD designs
  • Parts are CNC machined in-house from higher strength materials.
  • Lifts the front end 4.5 inches compared with stock
  • Widens track width 1.25 inches per side
  • Includes longer stainless braided front brake lines
  • Bolts on with all necessary hardware included

Alignment and driveline after lifting

Raising the front end changes the geometry that the alignment depends on, including caster and camber, and the driveline angles change too. Measure the angles after installation and have an alignment done before the truck is driven far. Ignoring these steps can cause uneven tire wear and vibration.

Longer brake lines should run without kinks or tension through the full suspension travel. Check the lines at each service, and look for chafing near the frame and steering components. Keep the brake fluid level in mind after line changes, since a new line run can trap air if it is bled poorly. Replace any line that shows wear.

  • Check the spindle bolts after the first few drives
  • Confirm the driveline angles are within a safe range
  • Inspect the stainless braided lines for chafing
  • Verify the ABS sensor wires have slack

Specifications

Brand Camburg Engineering
Part number CAMCAM-110123
Component Front spindles (knuckles), fabricated
Front lift 4.5 inches compared with stock
Lift with coilover 4.5 to 6.5 inches
Track width Increased 1.25 inches per side
Ground clearance Gain of 4.5 inches
Brake lines Longer stainless braided front lines
Fitment type Direct fit

Vehicle fitment

Camburg lists these spindles for the 2009–2013 Ford F-150 in FX2, FX4, Harley-Davidson Edition, King Ranch, Lariat, Lariat Limited, Limited, Platinum, STX, SVT Raptor, XL and XLT models.

The spindles are intended for 2WD F-150 trucks, though the fit also names the SVT Raptor and does not separate 4WD trims. Coverage ends with 2013 models. Confirm your drivetrain, year, model and trim before ordering.

Installation notes

The spindles bolt on with the hardware included, but the 4.5 to 6.5 inch figure assumes a coilover is combined with them. Raising the front end changes the alignment and the driveline angles, so have the front alignment checked and the driveline angles measured after installation.

What’s included

The kit includes fabricated spindles, the hardware needed to bolt them on, and longer stainless braided front brake lines. Coilovers are a separate purchase.

Fitment

VehicleYearsTrims
Ford F-1502009–2013FX2, FX4, Harley-Davidson Edition, King Ranch, Lariat, Lariat Limited, Limited, Platinum, STX, SVT Raptor, XL, XLT

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Does this spindle kit fit a 2012 F-150 4WD?

The spindles are intended for 2WD F-150 trucks, while the fit covers many 2009 to 2013 trims. Confirm the drivetrain before ordering, because 4WD trucks are not separated in the fit.

How much lift do the spindles give?

The spindles give 4.5 inches of lift compared with stock, and up to 6.5 inches when combined with a coilover. The extra lift comes from the spindle geometry rather than from pushing the coilovers to their limit.

Does it come with brake lines?

Yes. The kit includes longer stainless braided front brake lines, along with the hardware needed to bolt the spindles on. Check the brake lines against your installation before starting.

Do I need a new alignment after installing spindles?

Yes. Raising the front end changes the alignment geometry, so have the front alignment checked after installation. Measure the driveline angles too, since the changed height affects them and can cause vibration if left unchecked.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Ford F-150 Spindle on Amazon