Select your vehicle

Artec Industries Lower Link Axle Brackets – BR1010

Artec Industries

Shop Artec Industries Axle Brackets on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Artec Industries BR1010 lower link axle bracket, sold as a pair, part number A/IBR1010
  • Universal fit control arm mount, not tied to a specific vehicle
  • 2.625 mounting width with 9/16 bolt hole for common cartridge joints
  • Made from 1/4 thick boxed steel plate
  • Hole can be drilled out for 1.25 rod ends with spacers

Description

Overview

The Artec Industries BR1010 is a pair of lower link axle brackets, a control arm mount for fabricated suspension builds, sold as a pair under part number A/IBR1010. It is universal fit rather than built for one specific vehicle, so the mounting dimensions decide whether it suits your joints and tubes.

Artec Industries designed these brackets to look custom-made while addressing problems it sees with generic brackets, such as hard-to-reach grease fittings and unprotected joints. Each bracket is formed from 1/4 thick boxed steel plate, with a 2.625 mounting width and a 9/16 bolt hole sized for common cartridge joints. The design aims to look as though it was planned into the build from the start rather than added later.

Key features

  • Mounting width of 2.625 with a 9/16 bolt hole for common cartridge joints such as Johnny, Flex and Ballistic styles.
  • The hole can be drilled out to a larger size for 1.25 rod ends, using spacers.
  • Made from 1/4 thick boxed steel plate for strength and impact resistance.
  • Grease fitting access on top makes maintenance of the most worked joint easier.
  • A skid plate on the bottom of the bracket wraps around the joint to guard it from direct impact and reduce premature wear.
  • The skid plate design does not restrict joint movement.
  • Formed styling gives a custom one-off look instead of angle iron or C-channel.

Planning a fabricated link

A lower link is a load path, so the bracket needs to sit square to the axle and the link tube before anything is welded. Measure the joint, the bolt hole and the spacing first, then check that the mounting width suits the joint you plan to run. Small misalignment at the bracket shows up as binding through full travel.

Joint maintenance is easier when the grease fitting is reachable. Top-side access helps with routine greasing, but a fitting still needs clear room for the grease gun. Keep the skid plate clear of the joint so debris does not collect behind it, and check the boot and seal at each service interval.

Choose cartridge joints that match the bracket before you commit to a layout. Spacers and rod ends change the effective length, so dry fit the parts together and confirm there is enough thread engagement and clearance for full articulation.

Specifications

Brand Artec Industries
Part number A/IBR1010
Type Control arm mount
Sold as Pair
Material Boxed steel plate, 1/4 thick
Mounting width 2.625
Bolt hole 9/16
Rod end option Hole can be drilled out for 1.25 rod ends with spacers
Tube diameter Any
Fitment Universal fit

Vehicle fitment

Artec lists these brackets as universal fit, so no specific year, make or model is named. They are not vehicle-specific, but the 2.625 mounting width and 9/16 bolt hole must match your cartridge joints and link tube layout, so measure your joints before installing.

Confirm your vehicle’s year, model and trim before ordering.

Installation notes

Drilling the hole out for 1.25 rod ends is a separate job that needs spacers and a bit rated for steel plate, so check the joint size first. Wear eye protection when drilling.

What’s included

Sold as a pair of brackets.

Not included: Cartridge joints and mounting hardware need to be obtained separately.

Questions & Answers

Does the Artec Industries A/IBR1010 fit a specific vehicle?

No vehicle is named. Artec lists these brackets as universal fit, so they are not tied to a year, make or model. Check that the 2.625 mounting width and 9/16 bolt hole suit your cartridge joints and link tubes before ordering, since fit depends on your suspension geometry.

What joints and holes do these lower link brackets accept?

The bracket has a 2.625 mounting width and a 9/16 bolt hole for common cartridge joints, including Johnny, Flex and Ballistic styles. The hole can be drilled out to a larger size for 1.25 rod ends using spacers.

What is the Artec BR1010 bracket made from?

Artec Industries makes the BR1010 from 1/4 thick boxed steel plate for strength and impact resistance. A skid plate on the bottom wraps around the joint to protect it from direct impact and reduce premature wear without restricting joint movement.

Are joints or hardware included with the A/IBR1010?

The bracket is sold as a pair. Cartridge joints and mounting hardware are not included, so obtain joints separately and confirm the hole size matches them before ordering.

How often should the joints on lower link brackets be checked?

Check them at each service interval and after any trail session with heavy articulation. Look for dry joints, torn boots and play in the joint, since those signs usually mean the joint needs service or replacement.

Should the link angle be checked before final welding?

Yes. Set the bracket so the joint moves freely through full suspension travel without binding. Check the link tube alignment and the joint position before the final welds, because small errors show up as binding later.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Artec Industries Axle Brackets on Amazon