Select your vehicle

Trail Gear Driveline Spacer Kit – 105080-3-KIT

Trail Gear

$63.26In stock
Buy on Amazon

See similar parts on Amazon

Price and availability as of Nov 18, 2026 8:50 AM MST, from Amazon.com, and subject to change. The Amazon listing has the current details.

Check out with your Amazon account. Amazon handles delivery and returns.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Aluminum driveline spacer for the front or rear shaft
  • Mounting hardware included with each kit
  • Fits the 1986–1989 Suzuki Samurai

Description

Overview

The Trail Gear 105080-3-KIT is a driveline spacer kit for the 1986–1989 Suzuki Samurai, for use on the front or rear shaft.

The spacer is made from 6061 T6 aluminum, and the kit includes the mounting hardware. It fits the Samurai Base, JA, JX and JX SE models from 1986 to 1989.

Key features

  • Spacer made from 6061 T6 aluminum
  • Mounting hardware included
  • Fits the front or rear shaft

Spacing out the driveline

A driveline spacer adds a fixed length between two components, which can restore proper driveshaft angles after a change in ride height or a transfer case swap. Angles that are too steep cause vibration, binding of the joints and early wear, so the shaft should sit close to level in normal driving. Measure the existing angle before and after installing the spacer, and make small adjustments only when needed.

Aluminum is lighter than steel and is often chosen for trail use, where mud, water and road salt are common. Check the mounting bolts after the first drives and again after rough terrain, since spacers can loosen under vibration. Inspect the U-joints and the slip yoke at the same time, because worn joints often show up once the angle changes.

Before buying, confirm whether the shaft is front or rear and check that the spacer fits the joints already in place. Keep a record of the length used so any future lift or axle change can be planned with the original setup in mind.

Specifications

Brand Trail Gear
Part number 105080-3-KIT
UPC 70000621227
Material 6061 T6 aluminum
Fits Front or rear shaft
Contents One spacer and mounting hardware

Vehicle fitment

It fits the 1986–1989 Suzuki Samurai, including the Base, JA, JX and JX SE models.

The 1990–1995 Samurai is not on this list. Confirm your vehicle’s year, model and trim before ordering.

What’s included

One spacer and mounting hardware.

SKU: TGI105080-3-KIT Category:

Specification

Shipping weight 3.00 lbs
Package dimensions 7.50 × 7.50 × 3.50 in
brands

Fitment

VehicleYearsTrims
Suzuki Samurai1986–1989Base, JA, JX, JX SE

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Is the spacer aluminum?

Yes. It is made from 6061 T6 aluminum. Every kit contains one spacer and mounting hardware, so you do not need to source the hardware separately.

Will this kit fit a 1988 Suzuki Samurai?

Yes. It fits the 1986–1989 Suzuki Samurai, so a 1988 model is included. Confirm the front or rear shaft you are spacing before installing.

Does this kit cover the 1990 Samurai?

No. The Samurai entries for this kit end at 1989. The 1990–1995 Samurai is listed with a different Trail Gear spacer kit.

Is the spacer needed for every Samurai?

Not always. A spacer is needed when the driveshaft angle is off enough to cause vibration or joint wear, which often follows a lift or transfer case change. Measure the angle first, then decide whether a spacer of the length you need will correct it.

Ready to order?

Order this part on Amazon and check out with your Amazon account. Amazon handles delivery and returns.

Buy on Amazon