Overview
The California Super Trucks CSP-C28-6 is a high angle CV style front driveshaft for 2017–2018 Chevrolet Silverado and GMC Sierra 2500 HD and 3500 HD trucks, built for the Duramax and Allison combination.
The driveshaft is made for trucks with the CST Performance Suspension 6-8 inch lift system. It is built to reduce or eliminate driveline vibrations or noise in 4WD, which is the problem it addresses on those lifted trucks.
The shaft uses a dual universal joint cage, also called a dual cardan, at the transfer case side. That joint increases the angle the driveshaft can operate at, so it can run at steeper angles without binding, and removing the bind also removes the vibration that comes with it. The shaft is longer than a standard front driveshaft and is designed to work only with the CST 6-8 inch lifts.
Key features
- Dual universal joint cage (dual cardan) at the transfer case side
- The dual joint increases the operating angle the driveshaft can handle, allowing steeper angles without binding.
- Longer shaft designed for CST 6-8 inch lifts
- Designed to reduce or eliminate driveline vibrations or noise in 4WD
- Built for Duramax diesel and Allison transmission trucks
Driveline angles and lift
A front driveshaft on a lifted truck runs at a steeper angle than it was originally set for, and the joints at each end carry more of the load. A single joint can bind at a steep angle, which makes the driveline feel rough and can bring vibration in 4WD. Joint geometry, shaft length and transfer case output all affect how much angle the driveline can accept, so these parts should be checked as a set.
Before installing any driveshaft on a lifted truck, check the transfer case and front axle positions, the pinion angle and the length of the shaft. A shift linkage that is not adjusted for the new position can make 4WD engagement difficult, which is why the required bracket matters. Check the bolts on the transfer case flange and the yoke after the first drives, and look for movement or wear at the joint boots.
Vibration after a lift is often a sign of an angle problem rather than a worn driveshaft. Watch for shudder at highway speed, a clicking sound on turns or grease escaping from the joints. Keep the joints lubricated at the interval the vehicle requires, and replace any joint that shows play.
- Check transfer case flange bolts after the first drives
- Look for grease leaks at the joints
- Inspect the shift linkage for smooth 4WD engagement
- Recheck driveline angles after changing lift height
Specifications
| Brand | California Super Trucks (CST) |
|---|---|
| Part number | CSP-C28-6 |
| UPC | 700008389141 |
| Type | High angle CV style front driveshaft |
| Position | Front |
| Joint style | Dual universal joint cage (dual cardan) at the transfer case side |
| Required lift | CST 6-8 inch suspension lift |
| Engine and transmission | Duramax diesel with Allison transmission |
| Shift linkage | Low profile shift linkage bracket CSS-C22-13 required, sold separately |
| Fits | 2017–2018 Chevrolet Silverado and GMC Sierra 2500 HD and 3500 HD |
Vehicle fitment
It fits the 2017–2018 Chevrolet Silverado 2500 HD and 3500 HD and the 2017–2018 GMC Sierra 2500 HD and 3500 HD. Match your truck’s year, model and trim before ordering.
The driveshaft is designed for trucks with the CST 6-8 inch lift and the Duramax and Allison combination, so trucks with other lifts or powertrains are not the intended application.
The list does not include the 2011–2016 HD trucks, the 2019 and later models, or any 1500 series truck. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
The truck needs the CST 6-8 inch suspension lift before this driveshaft is installed, because the shaft is built for that lift height. A low profile shift linkage bracket, CSS-C22-13, is required and is sold separately, so plan for it before installation.
The shaft is longer than a stock front driveshaft and is sized for the CST lifts only. Using it on a truck with a different lift is outside the design.
What’s included
High angle CV style front driveshaft, part CSP-C28-6.
Not included: The low profile shift linkage bracket CSS-C22-13, which is sold separately, and the CST 6-8 inch suspension lift.









