Select your vehicle
-13%

Smittybilt Sure Step 3″ Diameter Side Bars (Textured Black) – JN40-S2T

Smittybilt

Shop Jeep CJ7 Nerf Steps on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Fits the 1976-1986 Jeep CJ7
  • 3-inch tube with textured black powder coat
  • 8-point frame mount and oversize bolt attachment
  • Non-slip polyester step pads
  • All installation hardware included

Description

Overview

The Smittybilt Sure Step 3-inch side bars, part number JN40-S2T, are textured black side steps for the 1976-1986 Jeep CJ7. Smittybilt lists them for the CJ7 and gives them a heavy-duty welded design with a rugged 8-point frame mount.

Each step pad is held in place by five pins in a squashed step, so there is no exposed metal to rust. The pads are non-slip polyester. An oversize bolt attachment keeps the tube from bouncing, and most applications install without drilling.

The bars run wheel to wheel and are made for the 1976-1986 Jeep CJ7.

Key features

  • 3-inch diameter tube
  • Textured black powder coat finish
  • Rugged 8-point frame mount
  • Non-slip polyester step pads
  • Oversize bolt attachment to reduce step bounce
  • Heavy-duty welded design

Preparing a CJ7 for side steps

The CJ7 sits high, so side steps make getting in and out far easier, especially with a soft top and half doors. Bars that run wheel to wheel also protect the lower body from brush and rocks on trails. Check the bar height against your body mounts and tire size before installing so the step sits where you need it.

Textured black powder coat holds up well to scrapes, but chips near the frame mounts can let moisture reach bare steel. Touch up any damage quickly, and check the body mounts after rough trail runs. Loose mounts can rattle and wear the holes in older body sheet metal over time.

On an older Jeep, rust in the frame and rocker area is common. Before mounting new bars, inspect the frame rails and mount points for cracks or soft spots, and repair them first. Clean the mounting surfaces and keep pads free of grit so they grip well when wet or muddy.

Specifications

Brand Smittybilt
Part number JN40-S2T
Tube diameter 3 inches
Length Wheel to wheel
Finish Textured black powder coat
Step pads Non-slip polyester
Mounting 8-point frame mount, body mount design
Drilling Not required on most applications
Fitment Direct fit

Vehicle fitment

Smittybilt lists these side bars for the 1976-1986 Jeep CJ7. The list covers only that model, so the CJ5 and the Wrangler YJ and TJ are not included.

Confirm your vehicle’s year, model and trim before ordering.

Installation notes

Most applications install without drilling, and all installation hardware is included. Because the bars mount to the frame and body, check the frame mount points on your CJ7 before you start.

What’s included

The side bars with step pads and all installation hardware.

Fitment

VehicleYearsTrims
Jeep CJ71976–1986Base, Golden Eagle, Golden Hawk, Laredo, Limited, Renegade

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Do the Sure Step side bars fit a 1976 to 1986 Jeep CJ7?

Yes. The side bars are for the 1976-1986 Jeep CJ7, and the 8-point frame mount is designed for that model. Check your model year and trim before ordering.

Do the side bars need drilling?

Most applications install without drilling. All installation hardware is included, so no separate mounting parts are needed to complete the install. Check the frame mount points on your CJ7 before you start.

Are the step pads slip resistant?

Yes. Smittybilt uses non-slip polyester step pads held by five pins in a squashed step. The design leaves no exposed metal, which Smittybilt says keeps the step from rusting.

How do I tell if a CJ7 frame mount needs repair?

Look for cracks, rust scale or soft metal around the mount holes, and for movement when you push on the bar. Any shifting or hole elongation means the mount should be repaired before you rely on the step. Reinforce weak spots before adding weight.

Can side steps be used with a soft top?

Yes, side steps are commonly used with soft tops, since they make the higher step from the ground easier. Check that the bars do not interfere with the door hinges or the soft top's lower edge when the doors are open.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Jeep CJ7 Nerf Steps on Amazon