Select your vehicle

Smittybilt Sure Step 3″ Diameter Side Bars (Stainless Steel) – TN1130-S4S

Smittybilt

Shop Toyota Tacoma Nerf Steps on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Fits the 2002–2004 Toyota Tacoma Base and Pre Runner versions
  • Stainless steel 3-inch side bar, cab length, sold as a pair
  • No-drill installation on most applications
  • Non-slip step pads and mounting hardware included

Description

Overview

The Smittybilt TN1130-S4S is a stainless steel side bar sold as a pair for the 2002–2004 Toyota Tacoma in its Base and Pre Runner versions. The bar is cut to cab length.

The bar is a 3-inch tube with a stainless steel finish. Each step pad is non-slip polyester, secured with five pins set into a squashed step, so the pad has no loose fastener and the metal underneath is not exposed to rust. The frame and body mount has an oversize bolt attachment to keep the tube steady.

Most applications are no-drill, and the mounting hardware is included with the pair. Confirm fit for your vehicle’s year, model and trim before ordering, since only the Base and Pre Runner versions are covered.

Key features

  • Stainless steel finish
  • Three-inch tube
  • Cab-length design
  • Non-slip polyester step pads
  • Five pins hold each pad in a squashed step
  • Frame and body mount design
  • No-drill installation on most applications
  • Sold as a pair

Tacoma cab-length bar basics

A cab-length side bar covers the area beside the cab, so it helps with getting in and out while leaving the bed and the rear quarter clear. On a Tacoma that sits high off the ground, a bar with a squashed-step pad gives a steadier foothold than a bare tube.

The 3-inch tube and oversize bolt attachment at the frame and body mount are where most of the load goes. Before installing, inspect the mounting points for rust, and clean the contact surfaces so the mount sits firmly against the frame.

Pads take the most wear, so inspect them regularly for cracks, sharp edges or loose pins. A stainless finish resists rust but still needs rinsing after trail use to remove mud and grit.

  • Clean mount contact surfaces before installing
  • Check pad pins and pad surfaces regularly
  • Rinse mud and grit after trail use

Specifications

Brand Smittybilt
Part number TN1130-S4S
Finish Stainless steel
Tube diameter 3 inches
Length Cab length
Step pads Non-slip polyester, secured with five pins
Installation No drilling on most applications
Quantity Sold as a pair

Vehicle fitment

It fits the 2002–2004 Toyota Tacoma in its Base and Pre Runner versions.

The black TN1130-S4B for the same years is a separate part, and the 2005 and later Tacoma are not covered. Confirm your vehicle’s year, model and trim before ordering.

What’s included

Two stainless bars, their pads and the hardware, in one kit.

SKU: S/BTN1130-S4S Categories: , ,

Fitment

VehicleYearsTrims
Toyota Tacoma2002–2004Base, Pre Runner

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Will the TN1130-S4S fit a 2004 Toyota Tacoma Pre Runner?

Yes. The list covers the 2002 to 2004 Tacoma in its Pre Runner version, so a 2004 Pre Runner is within the range. Check the rest of your truck's details against the list before ordering.

Does it fit a 2006 Tacoma?

No. The 2006 model year falls outside the 2002 to 2004 range this pair covers. Tacoma models from 2005 onward need a different side bar. Confirm fit for your vehicle's year, model and trim before ordering.

Is it sold as a pair?

Yes. The kit includes both bars and the mounting hardware for the cab-length fit. The finish is stainless steel, and the pair is supplied with everything needed to mount it on the listed Tacoma versions.

Do the step pads wear out before the bar?

They can. Pads take the most foot traffic, so they often show wear first. Check for cracks, loose pins and slick surfaces, and replace worn pads when they start to shift or lose grip.

How should a stainless bar be cleaned?

Rinse off mud and road salt with fresh water after trail use. Use mild soap and a soft cloth for stubborn grime. Avoid abrasive pads that can scratch the finish and hold dirt in the marks.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Toyota Tacoma Nerf Steps on Amazon