Select your vehicle
-13%

Rubicon Express CVF Drive Shaft – RE1898-165

Rubicon Express

Shop Rubicon Express Drive Shafts on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Rubicon Express RE1898-165 CVF rear drive shaft, extended length
  • Works with RE1807 and RE1801 slip yoke eliminator kits
  • Also compatible with Currie Enterprises tail shaft conversion kits
  • UPC 614901439496

Description

Overview

The Rubicon Express RE1898-165 is an extended rear CVF drive shaft built to work with the RE1807 and RE1801 slip yoke eliminator kits, as well as Currie Enterprises tail shaft conversion kits.

The shaft is universal fit, so the length comes from your own measurement. Measure from the flange face to the center of the rear U-joint, with the slip stub centered in its travel and the vehicle sitting on the ground in the running position.

Key features

  • Rear CVF drive shaft
  • Extended length
  • Works with RE1807 and RE1801 slip yoke eliminator kits
  • Works with Currie Enterprises tail shaft conversion kits
  • Slip yoke eliminator required

Matching the eliminator setup

The eliminator kit does more than fill the slip yoke. It sets the driveshaft length and the output shaft position, so the eliminator and the shaft have to be chosen as a pair. Mismatched parts can leave the joint at an angle it was not built for, which speeds wear at the front of the shaft.

When you plan a build, check the transfer case mounting and the rear axle pinion angle. A shaft that is too long can bind at full droop, and one that is too short can pull out of the transfer case. Mark the setup on paper before cutting or fitting any hardware.

Keep a record of the measurement used for the order. If the suspension height changes later with a lift or new springs, the length may need to be measured again.

  • Re-measure after any lift or spring change
  • Check transfer case output for play
  • Inspect the eliminator seal at each service

Specifications

Brand Rubicon Express
Part number RE1898-165
UPC 614901439496
Joint type CV
Length Extended
Position Rear
Fitment Universal fit
Slip yoke eliminator Required
Measured from Flange face to center of rear U-joint

Vehicle fitment

It is a universal fit shaft, so pair it with a compatible eliminator or tail shaft conversion kit. Confirm the length against your driveline before installation.

Confirm your vehicle’s year, model and trim before ordering, and verify the length against your own driveline.

SKU: R/ERE1898-165 Category:

Specification

Shipping weight 17.00 lbs
Package dimensions 20.00 × 4.00 × 4.00 in
brands

Questions & Answers

Is the RE1898-165 compatible with Currie tail shaft conversions?

Yes. It is compatible with Currie Enterprises tail shaft conversion kits. Confirm your conversion kit is a Currie kit before ordering this extended rear shaft, since the kit must match the shaft.

Does the RE1898-165 need an eliminator kit?

Yes. A slip yoke eliminator is required with this shaft. Choose the RE1807 or RE1801 kit, or a compatible tail shaft conversion, so the driveline setup matches the shaft.

What is the measuring point on the RE1898-165?

Measure from the flange face to the center of the rear U-joint, with the slip stub at the center of its travel. Do the measurement with the vehicle on the ground in the running position.

Do I need to re-check driveshaft length after a lift?

Yes. A lift changes the angles and the distance between the transfer case and axle, so measure again before installing a new shaft. Recheck the length after the lift is complete and the vehicle sits at its ride height.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Rubicon Express Drive Shafts on Amazon