Overview
The Poison Spyder BFH Front Bumper with Shackle Tabs and Brawler Bar (Bare), part number 13-16-020-DB, is a bare steel front bumper with an integrated winch mount for the 1987–1995 Jeep Wrangler (YJ). The stubby bumper is made from 3/16″ plate steel.
Poison Spyder says BFH stands for Built For the Hammers and that the bumper is designed for hardcore four-wheelers, with ground clearance, tire clearance and approach angle as priorities. It is no wider than the Jeep’s frame rails, with angled facets to help slide over rocks, and is CNC laser-cut from a single piece of 3/16″ plate steel and brake-formed. The Brawler Bar extends 7.4″ forward from the front edge of the bumper and is 9.8″ high, and the recovery shackle tabs are machined from 1″ thick plate steel for 3/4″ recovery shackles.
Key features
- Integrated winch mount and one-piece design
- CNC laser-cut and brake-formed from 3/16″ plate steel
- No wider than the Jeep’s frame rails, with angled facets
- Brawler Bar, a lower-profile stinger
- Brawler Bar extends 7.4 inch forward and 9.8 inch high
- Recovery shackle tabs machined from 1″ thick plate steel for 3/4″ shackles
- Tabs matched to the bumper angles for zero loss in approach angle
- Bare steel finish
Setting up winch and lights
The integrated winch mount is the start of a winch setup, but a winch has its own requirements. Match the winch’s rated pull to the vehicle’s weight and the loads you expect, and make sure the cable or rope length gives enough reach for the tabs and anchor points. The mount sits on a stubby bumper, so check that the winch body clears the grille and radiator when it is installed.
Light mounts are not included, so choose mounts sized for your lights before buying. Position lights so they clear the bumper face and do not block the grille, sensors or cooling airflow. Run the wiring with a fuse close to the battery, and secure the harness away from moving parts. Rust protection and periodic bolt checks keep the setup reliable.
- Winch rated for your vehicle weight
- Cable or rope length matched to anchor points
- Light mounts sized to the lights you choose
Specifications
| Brand | Poison Spyder Customs |
|---|---|
| Part number | 13-16-020-DB |
| UPC | 614901724462 |
| Product type | Front bumper (BFH) |
| Width | Stubby |
| Material | Steel, 3/16 inch plate steel |
| Finish | Bare |
| Brawler Bar | Extends 7.4 inch forward, 9.8 inch high |
| Shackle tabs | 1 inch thick plate steel, for 3/4″ recovery shackles |
| Winch mount | Included, integrated |
| D-ring mount | Included |
| Light mounts | Not included |
| Fitment type | Direct fit |
Vehicle fitment
The bumper fits the 1987–1995 Jeep Wrangler (YJ) in the Base, Islander, Laredo, Renegade, Rio Grande, S, SE, Sahara and Sport trims.
Later Wrangler generations, such as the TJ and JK, are not covered. The bumper has an integrated winch mount but does not include a winch or light mounts. Confirm fit for your vehicle’s year, model and trim before ordering.
Installation notes
Support the vehicle on jack stands or a lift on level ground, never on a jack alone. Tighten all fasteners to their specified torque and re-check them after the first miles of driving.
Bumpers are heavy, so use a second person or a lift to position them. After installation, check that any lights, cameras and sensors still work and that nothing contacts the tires at full steering lock.
If a winch is added, wire and fuse it following the winch’s own instructions, and use rated recovery shackles in the tabs.
Bare steel will rust if left unprotected, so plan to paint or coat the bumper.
What’s included
A bare steel front bumper with an integrated winch mount, a Brawler Bar and recovery shackle tabs, with a D-ring mount included.
Not included: a winch, recovery shackles, lights and light mounts, and paint or coating for the bare steel.
















