Select your vehicle
, ,

Omix-ADA Dana 18 Transfer Case Gasket – 18603.56

Omix-Ada

  • Omix-Ada OAI18603.56 Dana 18 transfer case to transmission gasket
  • Made for 6 cylinder engines
  • Fits 1967–1971 Jeep CJ5, CJ6 and J-series models

Purchase through Amazon

Orders are placed, shipped and supported through Amazon, with Amazon’s checkout, delivery options and return policy.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

Description

Overview

The Omix-Ada OAI18603.56 is a Dana 18 transfer case to transmission gasket for 6 cylinder engines. It fits 1967–1971 Jeep CJ5, CJ6, Commando, Jeepster and J-series models.

It fits a wide range of CJ, DJ, Dispatcher, Gladiator, Universal, Wagoneer (SJ) and J-100 through J-4800 models. Match your exact model and year before ordering.

Key features

  • Seals the joint between the Dana 18 transfer case and the transmission
  • Made for 6 cylinder engines
  • Direct fit for the Dana 18 to transmission joint
  • Covers many 1967–1971 CJ, DJ and J-series entries

Keeping the joint sealed

A transfer case to transmission gasket sits in a flat joint where oil, heat and vibration all work on the seal. Its job is to keep lubricant in the transfer case and dirt out, so even a small seep at this joint can drip onto the floor and leave a film on the underside of the vehicle. Gaskets compress over time, which is why a leak at the same joint often returns after a simple tightening.

Good preparation matters more than any single part. Scrape the old gasket material from both faces, clean them with a solvent that leaves no residue, and check the surfaces for warping or pitting before fitting the new gasket. Fasteners should be snug, tightened in the sequence the service procedure calls for, and checked again after the first drive. If the transfer case has been out for other work, a fresh gasket is a better choice than trying to reuse the old one.

  • Clean both mating faces thoroughly
  • Check for warped or pitted surfaces
  • Recheck fastener tightness after the first drive

Specifications

Brand Omix-Ada
Part number OAI18603.56
Transfer case Dana 18
Engine 6 cylinder

Vehicle fitment

Fits 1967–1971 Jeep CJ5 and CJ6 models, including CJ5A and CJ6A, plus Commando, Dispatcher, DJ5, DJ6, Gladiator, Jeepster, Universal, Wagoneer (SJ) and J-series trucks from J-100 through J-4800.

Years outside 1967–1971 are not in the list. Confirm your engine is a 6 cylinder and confirm your vehicle’s year, model and trim before ordering.

What’s included

The product is the transfer case gasket.

Not included: the transfer case, transmission or other gaskets.

Fitment

VehicleYearsTrims
Jeep CJ51967–1971Base
Jeep CJ5A1967–1968Base
Jeep CJ61967–1971Base
Jeep CJ6A1967–1968Base
Jeep Commando1967Base
Jeep Dispatcher1967Base
Jeep DJ51967–1971Base
Jeep DJ61967–1968Base
Jeep Gladiator1967Base
Jeep J-1001967–1971Base
Jeep J-25001967–1971Base
Jeep J-26001967–1970Base
Jeep J-27001967–1969Base
Jeep J-28001967Base
Jeep J-35001967–1970Base
Jeep J-36001967–1970Base
Jeep J-37001968–1970Base
Jeep J-38001967–1968, 1971Base
Jeep J-45001970–1971Base
Jeep J-46001970–1971Base
Jeep J-47001970–1971Base
Jeep J-48001971Base
Jeep Jeepster1967–1971Base, Commando
Jeep Universal1967Base
Jeep Wagoneer (SJ)1967–1971Base

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

What does the Omix-Ada OAI18603.56 gasket seal?

It is a Dana 18 transfer case to transmission gasket. It is made for 6 cylinder engines, so confirm your engine type before ordering.

Which 1967–1971 Jeep models does the Dana 18 gasket fit?

It fits CJ5 and CJ6 models, CJ5A and CJ6A, Commando, Dispatcher, DJ5 and DJ6, Gladiator, Jeepster, Universal, Wagoneer (SJ) and J-100 through J-4800 trucks. Confirm your year, model and trim before ordering.

Is this gasket a full transfer case rebuild kit?

No. The product is one gasket for the Dana 18 transfer case to transmission joint. Seals, bearings and other rebuild parts are not included and must be sourced separately.

Can the old gasket be reused?

Usually not. Gaskets compress and take a set once removed, so a new one gives the most reliable seal. Clean both mating faces thoroughly and check for warped or pitted surfaces before installing the replacement.