Select your vehicle

Mountain Off Road Enterprises Rod End – XML10-12

Mountain Off Road Enterprises

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Left-hand rod end with 3/4 inch – 16 shank and 5/8 inch bore
  • 52100 bearing steel ball, Teflon/Kevlar race, jam nut included
  • Universal Fit, part number XML10-12

Description

Overview

The Mountain Off Road Enterprises XML10-12 is a left-hand rod end with a 3/4 inch – 16 shank and a 5/8 inch bore. It is made for building your own tie rods, track bars, radius arms or link bars.

The rod end uses a 52100 bearing steel ball, a Teflon/Kevlar self-lubricating race and an alloy steel heat-treated body. The ball hole has the same diameter as the threaded shank on the body.

Key features

  • Left-hand thread direction
  • 3/4 inch – 16 shank
  • 5/8 inch bore
  • 52100 bearing steel ball with Teflon/Kevlar self-lubricating race
  • Alloy steel heat-treated body
  • Jam nut included, Universal Fit

Building a custom link

A homemade link is only as good as its joints, so start with the rod ends and plan the length around them. Measure the center-to-center distance you need, then thread each end in evenly so the link stays straight. Check that the ball pivots freely in both directions through the range the link will see. Keep the jam nut snug against the tube once the length is set, because a loose nut is the most common reason a custom link loses its alignment.

Use a tube and fittings matched to the load and the pin size, and weld only with the correct process for the material. After the first drives, recheck the setting, looking for wobble, play at the ball or a jam nut that has backed off. Carrying a spare jam nut and a wrench on longer trips makes roadside adjustments easy.

Specifications

Brand Mountain Off Road Enterprises
Part number XML10-12
UPC 70000461111
Shank 3/4 inch – 16
Bore 5/8 inch
Thread direction Left hand
Ball 52100 bearing steel
Race Teflon/Kevlar, self-lubricating
Body Alloy steel, heat-treated
Fitment Universal Fit

Vehicle fitment

Mountain Off Road lists Universal Fit, so this rod end is a build component rather than a vehicle-specific part.

No vehicle years, models or chassis codes are stated. Confirm your vehicle’s year, model and trim before ordering.

Installation notes

Left-hand threads turn opposite to standard right-hand threads, so confirm the tube or link you build also has left-hand threads before threading the rod end in.

What’s included

A rod end with a jam nut.

Not included: the tube, link or bar you build around the rod end.

SKU: MREXML10-12 Category:

Specification

Shipping weight 1.00 lbs
Package dimensions 5.00 × 5.00 × 5.00 in
brands

Questions & Answers

What is the XML10-12 rod end used for?

It is for building your own tie rods, track bars, radius arms or link bars. It is a left-hand rod end with a 3/4 inch - 16 shank, a 5/8 inch bore and a jam nut.

Is the XML10-12 left-hand or right-hand threaded?

It is left-hand threaded. Make sure the tube or link you build also has left-hand threads, since a right-hand tube will not match. Confirm the match before threading the rod end in.

Does the XML10-12 fit a specific vehicle?

No vehicle is named. Mountain Off Road lists Universal Fit, so this rod end is a build component rather than a part for one make, year or model. Check your linkage geometry before installing.

How do you set the length of a homemade link with a rod end?

Thread the rod end into the tube until the joint sits at the length you need, then tighten the jam nut against the tube. Check that the ball still pivots freely through its travel before the link goes on the vehicle.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon