Overview
The Currie CE-9120TJJ is an adjustable front trac bar with an offset Johnny Joint rod end, part number CE-9120TJJ, built for the Jeep TJ, XJ, LJ and MJ. A trac bar, also called a track bar, controls the axle’s side-to-side position under the vehicle, and an adjustable bar lets you re-center the axle after a lift. Currie presents this as an all-new and improved heavy duty version of its Johnny Joint design.
The offset Johnny Joint rod end moves the bar further forward, adding clearance between the differential and the trac bar. The bar is 1 1/4 inch by .250 wall 4130 chrome moly with a welded-in gusset running from the bar to the Johnny Joint, a heavy duty adjuster end with urethane bushing and steel insert sleeve, and a semi-gloss black powder coat finish.
Some drilling is required. The supplied frame bolt is 5/8 inch and the supplied housing bolt is 1/2 inch, and both holes must be drilled to size to accept the heavier duty hardware. A heavy duty nut plate kit is supplied for the housing end.
Key features
- Offset Johnny Joint rod end for more clearance between the differential and the trac bar
- 1 1/4 inch by .250 wall 4130 chrome moly construction
- Welded-in gusset from the bar to the Johnny Joint
- Heavy duty adjuster end with urethane bushing and steel insert sleeve
- Semi-gloss black powder coat finish
- Adjustable length
Setting up the track bar
A track bar controls the axle’s side-to-side movement, so it needs correct length and secure ends to keep the axle centered. Adjustable bars make it possible to re-center the axle after a lift, but every length change should be followed by an alignment check. Keep a record of the setting so you can return to it after a service. Look at the bar ends and frame mounts after each off-road trip.
Heavier bars and enlarged holes place more load on the frame and housing, so inspect the surrounding mounts for cracks or elongation after installation. Lift height, tire size and axle position all affect the correct bar length, so measure before final tightening. Replace worn ends or bushings promptly if you notice play or knocking when the steering is turned.
- Check bar length after changing lift
- Inspect frame and housing mounts for cracks
- Replace worn ends or bushings promptly
Specifications
| Brand | Currie |
|---|---|
| Part number | CE-9120TJJ |
| UPC | 70000533408 |
| Position | Front |
| Tubing | 1 1/4 inch by .250 wall, 4130 chrome moly |
| Rod end | Offset Johnny Joint |
| Frame bolt | 5/8 inch, supplied (drill to size) |
| Housing bolt | 1/2 inch, supplied, heavy-duty housing bolt (drill to size) |
| Finish | Semi-gloss black powder coat |
| Fitment type | Direct fit |
Vehicle fitment
The bar is built for the Jeep TJ, XJ, LJ and MJ chassis. It covers the Jeep Wrangler TJ from 1997 to 2006, the Cherokee XJ from 1984 to 2001, the Wrangler LJ from 2004 to 2006 and the Comanche MJ from 1986 to 1992.
Other Jeep generations, including the JK Wrangler, fall outside this fitment. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
Drilling is required, so the bar is not a simple bolt-on until the frame and housing holes are enlarged. Drill to the size of the supplied 5/8 inch frame bolt and 1/2 inch housing bolt, then fit the heavy duty nut plate kit at the housing end. Have the track alignment checked after setting the bar length, because changing the length moves the axle position. Support the axle with stands while drilling.
What’s included
The bar includes the supplied 5/8 inch frame bolt, the heavy-duty housing bolt and a heavy duty nut plate kit for the housing end.
Not included: Drill bits and drilling equipment are needed to enlarge the holes.





