Overview
The Bilstein 5100 Series Shock Absorber 24-146708 is a front monotube gas pressure shock for the 2007–2018 Jeep Wrangler (JK), for a front lifted height of 1.5-3″. It measures 24.63 inches extended and 14.98 inches collapsed, with 9.65 inches of travel.
The 5100 Series uses a single tube high gas pressure design for consistent performance and long life on lifted trucks and Jeeps. It has self-adjusting deflecting disc valving, a high-flow piston, independent rebound and compression tuning, and a larger working piston area. It is built for specific lift kits using the stock O.E.M. mounting configuration. Wheel spacers or aftermarket offset wheels are required.
Key features
- Monotube gas pressure construction
- Self-adjusting deflecting disc valving
- High-flow piston reduces harshness
- Independent rebound and compression tuning
- Larger working piston area for exact damping
- Stock O.E.M. mounting configuration
- Zinc plated finish; boot included
- For front lifted height 1.5-3″
Lift kits and ride height
Front shocks on a lifted Jeep work harder because the suspension is longer and the steering and axle angles change. A shock tuned for a specific lift height can feel stiff or soft if the height is wrong, so the ride height should match the shock’s intended range before the truck is driven on the road. Matching shock length and travel to the lift keeps the front end stable at speed.
Wheel and tire changes that come with a lift need separate attention. Clearance through full steering and suspension travel matters, and heavy tires can add load to the front shocks and mounts. Re-check the lift components, bushings and shock mounts after the first few drives, and keep the tires at the correct pressure to reduce strain on the suspension.
- Confirm lift height matches the shock range
- Check clearance through full steering travel
- Inspect mounts and bushings after the first drives
- Replace front shocks in pairs
Specifications
| Brand | Bilstein |
|---|---|
| Part number | 24-146708 |
| UPC | 651860598499 |
| Product type | Shock absorber (5100 Series) |
| Position | Front |
| Lift height | 1.5-3″ front lifted height |
| Collapsed length | 14.98 inches |
| Extended length | 24.63 inches |
| Travel length | 9.65 inches |
| Lower mount | Eye 12.1mm |
| Upper mount | Stem |
| Shaft diameter | 14mm |
| Body design | 46mm ID smooth body (non-coilover) |
| Internal design | Mono tube |
| Reservoir | No |
| Finish | Zinc plated |
| Boot included | Yes |
| Sold as | Each |
| Gas or hydraulic | Gas charged |
| Fitment type | Direct fit |
Vehicle fitment
It fits the 2007–2018 Jeep Wrangler (JK) in the 75th Anniversary, Rubicon, Sahara, Sport, Sport S, Unlimited 75th Anniversary, Unlimited Rubicon, Unlimited Sahara, Unlimited Sport, Unlimited Sport S, Unlimited X and X trims.
It is not for Wrangler TJ or JL models. It is a front shock for a front lifted height of 1.5-3″, and wheel spacers or aftermarket offset wheels are required. Confirm fit for your vehicle’s year, model and trim before ordering.
Installation notes
Tighten all fasteners to the specified torque. Support the vehicle on jack stands or a lift on level ground, never on a jack alone, and re-check fastener tightness after the first miles of driving.
Suspension work changes ride height, steering geometry and brake line and driveline clearances, so professional installation is recommended, and a wheel alignment is advised afterward. Check your local regulations on vehicle lift height and equipment.
Wheel spacers or aftermarket offset wheels are required, so check tire and wheel clearance through full suspension and steering travel after installation.
What’s included
One shock absorber with a boot, sold each.
Not included: a second shock for the other side, and wheel spacers or offset wheels, which are required for this kit.












