Overview
The Baer Brakes 31425-020 is a pair of Claw performance front brake rotors for the 2005–2007 Nissan Titan, 2005–2006 Nissan Armada and 2005–2009 Infiniti QX56. Each rotor is one-piece, full cast iron and vented, with a slotted and cross-drilled friction surface, sold as a set of direct replacements.
Brake rotors, also called brake discs, are the surface the pads clamp against to slow the wheel. The slots and drilled holes on this design give hot gases and pad dust a path out from between the pad and rotor. The design supports consistent pedal feel and reduces brake fade. The zinc-plated finish looks bright through open center wheels.
Key features
- Slotted and cross-drilled face clears gases and dust from the pad-to-rotor contact area.
- Enhanced vane structure and premium materials are aimed at cooling and durability.
- Mill balanced, premium grade rotor designed as a direct replacement.
- Chamfered cross-drilled holes are meant to reduce the risk of stress cracking.
- Zinc-plated surface gives a bright look behind open center wheels.
- Directional brake surface, sold as a set containing a pair of rotors.
Pad bedding and rotor wear
A new rotor works best when the pads are matched to it. Pads that are worn unevenly or glazed can leave the friction surface with hot spots and deposits, so replacing pads at the same time as rotors is a common approach. Bedding in new pads gradually, with several moderate stops rather than one hard stop, helps the pad material transfer an even layer onto the rotor face.
Rotors wear over time through normal friction, and the slots and cross holes on a drilled design can deepen this wear at the edges. Look for deep grooves, cracks around the drilled holes, blue discoloration, or a pulsing pedal under braking. Any of these signs means the rotor should be measured and replaced if it is near or below its minimum thickness.
- Replace pads and rotors as a matched pair when possible
- Bed in new pads with gradual stops before towing or hard braking
- Check for pulsation, scoring and heat discoloration at each pad change
Specifications
| Brand | Baer Brakes |
|---|---|
| Part number | 31425-020 |
| UPC | 844165031154 |
| Sold as | Set (pair of rotors) |
| Axle | Front |
| Construction | One piece, full cast |
| Rotor type | Vented |
| Surface type | Slotted and drilled |
| Brake surface | Directional |
| Material | Cast iron |
| Disc finish | Zinc plated |
| Grade | Premium |
| Outside diameter | 318.5 |
| Overall height | 43.3 |
| Mounting bolt hole circle diameter | 114 |
| Stud/lug hole quantity | 6 |
| Discard thickness | 24.6 |
| Emission code | 6 |
| ABS tone ring included | No |
| Country of origin | CN |
Vehicle fitment
The manufacturer fitment list covers these front positions: 2005–2007 Nissan Titan (noted as 03/05 thru 2007), 2005–2006 Nissan Armada (03/05 thru 10/06, with Bosch front calipers and 320mm front rotors) and 2005–2009 Infiniti QX56 (03/05 thru 09/06, with 320mm front rotors).
The Armada and QX56 entries end at 10/06 and 09/06, so later build months are not covered by this list. The Armada entry also requires Bosch front calipers, and both entries require 320mm front rotors. Rear rotors and other Nissan or Infiniti models are not covered. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
The rotors are direct replacements. Because the Armada and QX56 fit depends on caliper and rotor configuration, compare your existing calipers and rotor size before starting. Brake work is safety-critical, so have it done by someone trained in brake service.
What’s included
A pair of Baer Claw front rotors, sold as a set.
Not included: ABS tone ring.
















