Overview
The Crown Automotive 6034988 is a 3/8 in. – 24 distorted thread conical lock nut for use as an axle nut. It fits a wide range of Jeep models, including the 1987–1995 Wrangler YJ, the 1998–2006 Wrangler TJ, the Cherokee XJ and SJ, the CJ5, CJ7, Comanche and Grand Cherokee WJ.
The nut has a distorted thread, which makes it a lock nut that resists loosening. Its conical seat and 24 thread pitch let it be matched to the fastener it replaces.
It is a locking hub spindle nut, so it suits owners servicing hubs and axle ends on older Jeep models.
Key features
- Axle nut
- 3/8 in. – 24 thread
- Distorted thread conical lock nut
- Fits Wrangler YJ and TJ
- Fits Cherokee XJ, Comanche, CJ5, CJ7 and Grand Cherokee WJ
- Direct-fit replacement part
Inspecting hub and axle fasteners
A conical lock nut holds a hub or axle component under constant load, so its condition affects how safely the wheel stays attached. Look for thread damage, cracks, flattened lock features or rust before reinstalling. A nut that spins freely or has lost its grip should be replaced, not reused.
Clean the spindle threads before installing so the nut seats evenly and the thread does not bind. Pay attention to the thread size, since a near-match in pitch can strip the spindle or cross-thread the nut. Stop and recheck if a nut starts crooked or resists turning early, and do not force it.
Hub service usually involves bearing, seal and washer work, so inspect those parts at the same time. Older Jeep axles see decades of wear, and worn parts often show up in the same area.
Specifications
| Brand | Crown Automotive |
|---|---|
| Part number | 6034988 |
| UPC | 849603006701 |
| Part type | Axle nut |
| Thread size | 3/8 in. – 24 |
| Nut style | Distorted thread conical lock nut |
| Fitment type | Direct fit |
| Category | Axle parts, locking hub spindle nuts |
Vehicle fitment
It fits these vehicles, with the trims shown:
- 1981–1983 Jeep Cherokee (SJ) (Base, Chief, Pioneer)
- 1984–1996, 1999–2001 Jeep Cherokee (XJ) (Base, Briarwood, Chief, Classic, Country, Laredo, Limited, Pioneer, SE, Sport)
- 1977–1983 Jeep CJ5 (Base, Golden Eagle, Laredo, Limited, Renegade)
- 1977–1986 Jeep CJ7 (Base, Golden Eagle, Golden Hawk, Laredo, Limited, Renegade)
- 1986–1992 Jeep Comanche (Base, Chief, Custom, Eliminator, Laredo, Pioneer, X, XLS)
- 1999–2004 Jeep Grand Cherokee (WJ) (Laredo, Limited, Overland, Special Edition, Sport)
- 1984–1991 Jeep Grand Wagoneer (SJ) (Base, Limited)
- 1981–1988 Jeep J10 (Base)
- 1981–1988 Jeep J20 (Base)
- 1981–1985 Jeep Scrambler (Base, Laredo, Renegade, SL, SR)
- 1981–1990 Jeep Wagoneer (SJ) (Base, Brougham, Limited)
- 1998–2006 Jeep Wrangler (TJ) (65th Anniversary Edition, Rubicon, SE, Sahara, Sport, X)
- 1987–1995 Jeep Wrangler (YJ) (Base, Islander, Laredo, Renegade, Rio Grande, S, SE, Sahara, Sport)
The Wrangler TJ is covered from 1998 to 2006 and the Wrangler YJ from 1987 to 1995. Confirm fit for your vehicle’s year, model and trim before ordering.
Installation notes
Check the thread size of the fastener you are replacing against this nut’s 3/8 in. – 24 thread before installing. Use your vehicle’s service procedure for torque values.









