Select your vehicle

Recon LED Resistor Kit – 26420

Recon

Shop Recon LED Resistor on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Recon LED resistor kit, part number 26420
  • 6 Ohm, 50 Watt load resistor for signal and brake lights
  • Simulates a 2 Amp filament bulb load across turn signal bulbs
  • Addresses hyper flashing and bulb-out warnings after LED swaps
  • Universal fit

Description

Overview

The Recon LED Resistor Kit, part number 26420, is a 6 Ohm, 50 Watt load resistor for signal and brake lights that use dual filament LED bulbs. It is designed for LED-equipped vehicles whose turn signals flash too fast or show a bulb-out warning after an LED swap. It is a universal fit and wires across the bulb circuit rather than fitting a specific vehicle.

LED bulbs draw very little power, so some newer vehicles read the low current as a burnt-out bulb. Some cars respond by increasing the flash rate of the turn signals, while others turn on a bad bulb indicator. Recon’s load resistors are wired across the turn signal bulbs to simulate the load of a regular filament bulb, which Recon gives as a 2 Amp load. This addresses hyper flashing and burnt-out bulb indications caused by LED swaps.

Key features

  • 6 Ohm, 50 Watt load resistor rating
  • Simulates a filament bulb load of 2 Amp
  • Wired across turn signal bulbs
  • Designed for signal and brake lights with dual filament LED bulbs
  • Addresses hyper flashing and bulb-out indications

Heat and wiring checks

A load resistor draws the small amount of current an LED bulb no longer draws, so the flasher sees a load closer to a filament bulb. That energy leaves as heat, which makes placement as important as wiring. Keep the resistor away from harness insulation, fuel lines and plastic trim, and leave room around it so air can move past.

Load resistors are often added after a full LED conversion, so review the rest of the lighting circuit too. Worn sockets, corroded contacts or a weak ground can cause flicker that a resistor will not fix. If the flash rate returns to normal once the resistor is connected, the resistor is doing its job. If the problem continues, test the wiring before adding more parts.

  • Inspect the resistor body and wiring for discoloration after the first few drives
  • Re-check connectors and mounting screws after the first week of use
  • Keep the resistor clear of fuel lines and brake hoses

Specifications

Brand Recon
Part number 26420
UPC 70000496113
Resistance 6 Ohm
Power rating 50 Watt
Simulated filament load 2 Amp
Application Signal or brake lights with dual filament LED bulbs
Fitment Universal fit

Vehicle fitment

The kit is a universal fit, so it is not tied to one make, model or year. Suitability depends on your turn signal and brake light wiring, so inspect that wiring before connecting the resistor.

Installation notes

Wire each resistor across the turn signal bulb, following the connection Recon describes for the kit. Mount the resistor where its heat cannot reach nearby wiring or plastic, since a 50 Watt resistor runs hot. Disconnect the battery before working on the lighting circuit.

What’s included

The kit contains resistors for turn signal and brake light bulbs. Count the parts and confirm the wiring leads before starting the installation.

SKU: REC26420 Category:

Specification

Shipping weight 0.10 lbs
Package dimensions 4.00 × 1.00 × 1.00 in
brands

Questions & Answers

Will the Recon LED Resistor Kit 26420 fix hyper flashing?

It is designed for that job. Recon wires these 6 Ohm, 50 Watt resistors across the turn signal bulbs to simulate a filament bulb load, which addresses hyper flashing and bulb-out warnings caused by LED bulbs.

Is part number 26420 vehicle specific?

No. The resistor kit is a universal fit, so it is not built for one make, model or year. Confirm that your turn signal and brake light wiring suits a load resistor before connecting it.

What load does the resistor simulate?

The resistors simulate the load of a regular filament bulb, a 2 Amp load. They are rated at 6 Ohm and 50 Watt and are intended for signal and brake lights with dual filament LED bulbs.

Do all LED swaps need a load resistor?

No. Resistors are usually needed when the turn signals flash too fast or show a bulb-out warning after an LED swap. If the flash rate stays normal with the new bulbs, a resistor may not be needed.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Recon LED Resistor on Amazon