Overview
The Poison Spyder Brawler Rocker 17-08-200 is a two-piece bare steel rocker armor for the 2007–2016 Jeep Wrangler JK, 2-door models. It is a mini-boatside design built from 3/16-inch plate steel.
Poison Spyder says each piece is CNC laser cut and precision brake formed. The upper piece fits the lower sheet metal of the JK closely, with protection similar to Poison Spyder’s JK Body Armor. The lower piece carries the rub rail, which protrudes about 3-1/4 inches outboard of the body tub, and its top surface can also serve as an entry step.
Below the rub rail, the boatside angles down and inward, so the Jeep can slide off rocks and obstacles and back onto the center of the trail. It also keeps trees and rock walls a safe distance from the doors.
Inside, an array of 3/16-inch gussets adds strength. Oval lightning holes along the boatside let mud and debris be hosed out after a day on the trail. The ends are capped in the same plate steel, with angled facets that allow up to a 40-inch tire and visually match Poison Spyder’s front and rear JK Crusher Flares.
The upper piece attaches to the body tube, and the lower piece attaches to the upper piece and ties in at the body mounts. This spreads the load across several planes for triangulated strength. The ends also give a lifting point for a Hi-Lift jack when changing a tire or performing an extraction.
Key features
- Two-piece mini-boatside design in 3/16-inch plate steel
- CNC laser cut and precision brake formed construction
- Rub rail protrudes about 3-1/4 inches outboard of the body tub
- Boatside angles so the Jeep can slide off rocks
- Internal 3/16-inch gussets and oval lightning holes for hosing out mud
- Countersunk fastener holes and angled ends for up to a 40-inch tire
- Hi-Lift lifting point on the ends
Protecting the lower body
Rocker armor takes the hits that would otherwise reach the rocker panels and doors, so the way it attaches to the body matters as much as the steel itself. A two-piece design allows the lower piece to be replaced if it is damaged, while the upper piece stays in place. Check the upper attachment at the body tube and the lower attachment at the body mounts for any movement after hard trail use.
Gussets inside the rocker add strength where the plate meets the body. Hosing out the oval holes after a day of mud keeps the inside clean and reduces trapped water. Watch for dents that change the angle of the boatside, since a bent surface can catch rocks instead of sliding over them.
Rocker armor is also a convenient place to attach recovery or lift points, so check those points before each use. Keep the nut-serts and clip-nuts tight, and look for cracks around the mounting holes.
- Recheck the upper attachment
- Hose out the lightning holes
- Watch for dents at the boatside
Specifications
| Brand | Poison Spyder Customs |
|---|---|
| Part number | 17-08-200 |
| UPC | 614901726787 |
| Finish | Bare steel |
| Material | 3/16-inch plate steel |
| Configuration | Two-piece boatside |
| Rub rail projection | About 3-1/4 inches |
| Tire clearance | Up to a 40-inch tire |
| Hardware | Stainless steel flat-head cap screws, nut-serts and clip-nuts |
| Body lift compatibility | Not compatible with body lifts |
| Installation | Cutting or drilling required |
| Fitment type | Direct fit |
Vehicle fitment
Poison Spyder lists these rockers for the 2007–2016 Jeep Wrangler JK, 2-door models. They are built to fit the lower sheet metal and body tub of that generation.
Confirm fit for your vehicle’s year, model and trim before ordering, especially for four-door Wrangler Unlimited and JL models.
Installation notes
Installation requires cutting or drilling, so these rockers are not a simple bolt-on. They are not compatible with body lifts, so confirm your lift type before ordering.
What’s included
The two-piece rocker armor, with the stainless steel flat-head cap screws, nut-serts and clip-nuts supplied for mounting.
















