Select your vehicle

Fab Fours Vengeance Front Bumper (Black) – DR10-V2951-1

Fab Fours

Shop Ram 2500 Front Bumpers on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Vengeance lightweight front bumper for 2010 to 2018 Ram 2500 and 3500
  • Center cutout for a 20-inch LED light bar, not included
  • Lower cutout for intercooler airflow
  • 11 ga. steel, two-stage black powder coat

Description

Overview

The Fab Fours DR10-V2951-1 is a Vengeance Series front bumper for 2010 to 2018 Ram 2500 and 3500 trucks, a lightweight non-winch steel sensor bumper in a two-stage black powder coat.

The Vengeance line is Fab Fours’ lightweight bumper range. This version has a center cutout sized for a 20-inch LED light bar and side positions for two 2×2 Dually lights, neither of which is included. A lower cutout lets air reach the intercooler, and brackets tie the bumper directly to the frame. The fit is high and tight, with a sleek, aggressive look on and off the road. It is offered with no guard or with a pre-runner guard, and the same design is made for the front and rear of a vehicle.

Key features

  • Lightweight design: Fab Fours lists 65 lb for the no guard version and 75 lb for the pre-runner guard version
  • Center mount for an integrated 20-inch LED light bar
  • Side mounting options for two 2×2 Dually lights
  • Lower cutout for airflow to intercoolers
  • Complete bolt-on bumper with brackets tied to the frame
  • Two-stage black powder coat
  • 11 ga. U.S. steel construction
  • Made in the USA

Choosing LED lights for a bumper

A center light bar mount changes how the bumper is used at night, so think about beam height before adding one. A bar sitting too high can throw light into oncoming traffic, while one set too low may only light the ground in front of the bumper. Side Dually lights spread the beam wider and suit close trail work.

Wiring matters as much as placement. Run lights through a fused relay tied to a switch, and route the harness away from hot exhaust parts and moving linkage. Recheck the aim after the first few hard drives, since mounts can settle. A lower cutout should stay open so the intercooler still gets air, even with lights mounted near it.

  • Aim the beam level for the terrain you drive
  • Use a fused relay for each light circuit
  • Secure harness clips away from heat and moving parts
  • Keep the lower intercooler cutout unobstructed

Specifications

Brand Fab Fours
Part number DR10-V2951-1
UPC 5810110871
Type Vengeance front bumper, non-winch
Position Front
Width Full
Material Steel, 11 ga. U.S. steel
Finish Two-stage black powder coat
Fit type Direct fit
Light mounts Included
Winch mount Not included; non-winch bumper
Sensors Designed as a sensor bumper

Vehicle fitment

It fits the 2010 Dodge Ram 2500 and 3500 and the 2011 to 2018 Ram 2500 and 3500.

The list does not include Ram 1500 trucks or 2019 and newer heavy-duty models. Confirm your vehicle’s year, model and trim before ordering.

Installation notes

The bumper bolts on using the supplied brackets, which attach directly to the truck’s frame. If an LED bar or Dually lights are wanted, wire them through a fused relay.

What’s included

  • Vengeance front bumper in black powder coat
  • Frame-mounting brackets

Not included: The 20-inch LED light bar and the 2×2 Dually lights.

SKU: FFIDR10-V2951-1 Category:

Specification

Shipping weight 125.00 lbs
Package dimensions 84.00 × 30.00 × 26.00 in
brands

Fitment

VehicleYearsTrims
Dodge Ram 25002010Laramie, Power Wagon, SLT, ST, SXT, TRX
Dodge Ram 35002010Laramie, SLT, ST, SXT
Ram 25002011–2018Big Horn, Laramie, Laramie Limited, Laramie Longhorn, Limited, Lone Star, Outdoorsman, Power Wagon, SLT, ST, Tradesman
Ram 35002011–2018Big Horn, Laramie, Laramie Limited, Laramie Longhorn, Limited, Lone Star, SLT, ST, Tradesman

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Does the Vengeance bumper include the LED light bar?

No. The bumper has a center position for a 20-inch LED light bar and side mounts for two 2x2 Dually lights, but the lights themselves are not included.

Is the DR10-V2951-1 a winch bumper?

No. This bumper has no winch mount. The Vengeance Series is light by design, so it is not meant for winch use.

How does the Vengeance bumper attach?

It is a complete bolt-on bumper. The supplied brackets tie directly to the frame, so installation uses the brackets that come in the box.

Which Ram trucks does the DR10-V2951-1 fit?

It fits the 2010 Dodge Ram 2500 and 3500, and the 2011 to 2018 Ram 2500 and 3500. Ram 1500 trucks are not covered by this bumper.

Can I add a light bar after installing the bumper?

Yes. The center position and the side positions are made for lights, so a bar or Dually lights can be added later. Wire them through a fused relay and check the aim once the truck is at its normal ride height.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Ram 2500 Front Bumpers on Amazon