Overview
The Baer Brakes Track4 front brake system in red, part number 4301406R, is a preassembled front kit for GM G-Body, S10 and S15 vehicles. Its 4-piston T4 caliper grips a 13.0 inch one-piece slotted, drilled rotor, and the hubs arrive on stock height spindles.
The billet aluminum hubs carry premium bearings packed with Redline synthetic grease, along with billet dust caps. The package includes mounting brackets, stainless braided hoses and hardware. The 13 inch Track4 is suited to most 17 inch or larger wheels, and aftermarket wheels may not all clear, so check your wheel against the Q082H template.
Key features
- 4-piston T4 caliper in red with a powder coated finish
- Stainless steel pistons, abutments and noise suppression clips
- Staggered pistons designed to minimize uneven pad wear
- Dual seals against dust, weather and pressure
- One-piece slotted, drilled and zinc-plated rotor
- Stock height spindles with billet aluminum hubs
Things to check
Before installing a front brake kit on an older GM platform, look over the surrounding parts that the new brakes depend on. Wheel bearings, steering components and ball joints all carry load through the same spindle, so any play or wear in them will show up as vibration or pull once the new rotor is in service. Replace worn items while the wheel is off, since the job is much easier at that point.
Braided hoses and dust caps are easy to overlook but need regular attention. Look for scuffing where the hose passes near the suspension, and check that the banjo fittings are snug without being overtightened. The rotor surface should be checked for scoring or heat cracks after the first trail or street use, and the pads should be replaced in pairs so that braking stays balanced across the axle.
- Check wheel bearings and ball joints for play
- Inspect braided hoses where they pass the suspension
- Look for scoring or heat cracks on the rotor
- Replace pads in pairs across the axle
Specifications
| Brand | Baer Brakes |
|---|---|
| Part number | 4301406R |
| UPC | 844165042020 |
| Sold as | Kit |
| Axle | Front |
| Drive | 2WD |
| Caliper | T4, 4-piston, fixed, red |
| Brake pad FMSI number | D0749 |
| Rotor outside diameter | 13.0 inch |
| Rotor thickness | 1.1 |
| Rotor type | 1-piece, vented |
| Rotor surface | Slotted, drilled and zinc plated |
| Wheel bolt pattern | 5×4.75 |
| Lug count | 5 lug |
| Wheel stud size | M12-1.50 x 51.5mm |
| Minimum wheel diameter | 17.0 inch |
| Brake hose | Steel braided, DOT approved |
| Spindles | Stock height, included |
| Grade | Performance |
| Fitment template | Q082H |
| Country of origin | US |
Vehicle fitment
The listed fitment for the red Track4 matches the silver version and includes these models:
- Buick Regal, 1978–1988
- Chevrolet El Camino, 1978–1987
- Chevrolet Malibu, 1978–1983
- Chevrolet Monte Carlo, 1978–1988
- Chevrolet S10, 1982–2003
- Chevrolet S10 Blazer, 1983–1994
- GMC S15, 1982–1990
- GMC S15 Jimmy, 1983–1991
- Oldsmobile Cutlass, 1978–1981 and 1985–1988
- Oldsmobile Cutlass Supreme, 1978–1988
- Pontiac Grand Prix, 1978–1988
Any make, model or year range absent from this list is not covered. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
The hubs arrive on stock height spindles already built, so no bearing packing is needed on your end. Compare the Q082H template with the wheels you plan to use, keeping the 17.0 inch minimum wheel diameter in view. Brake components are safety-critical, so a qualified technician should install the kit and test it before driving.
What’s included
The Track4 system with pre-assembled hubs, mounting brackets, stainless braided hoses, hardware and front rotor. Lug nuts are not included.
Not included: Lug nuts.














