Overview
The Baer Brakes 4262683FR is a dual deep stage rear brake kit for Ford 9 inch small bearing housing ends, sold as a set and built for drag racing and heavy, fast cars that may also see street use. It includes two sets of calipers, four S4 units in Fire Red, clamping 11 inch two-piece slotted and drilled rotors.
The SS4 Plus Dual Deep Stage is Baer’s smaller-package drag system, designed to carry the benefits of its larger brake systems into a package that suits 15 inch and larger wheels. The pads are the DR1 or HB100 type, and the high friction compound is intended for drag race applications. Manufacturing is in Phoenix, Az.
Key features
- Two sets of S4 calipers, four 4-piston calipers in total with 1.375 inch pistons
- Hard anodized aluminum pistons with stainless steel abutments and noise suppression clips
- Two-piece rotors, slotted, drilled and zinc plated, with iron rotor and aluminum hat
- Billet aluminum hats drilled for 5/8 inch wheel studs
- Rotors pre-assembled with NAS high grade stainless hardware
- Powder coated Fire Red finish
Dual caliper setup considerations
A dual rear setup places two sets of calipers on the same axle, so the braking load is shared across more pistons and pads. Pads on both sets should wear evenly. Uneven wear can point to caliper alignment, pad seating or a sticking piston, so check each caliper after the first few sessions.
Hose routing and line length become more involved with extra calipers, so plan the layout before final assembly. Keep hoses clear of the exhaust, suspension travel and moving parts. Use a consistent fluid and bleed the entire circuit to remove air, since a spongy pedal often comes from trapped air.
- Compare pad wear across all calipers
- Route hoses clear of heat sources and moving parts
- Bleed the full circuit after any hose change
Specifications
| Brand | Baer Brakes |
|---|---|
| Part number | 4262683FR |
| UPC | 844165038962 |
| Sold as | Set |
| Caliper | S4, 4-piston, fixed, Fire Red, dual set |
| Piston size | 1.375 inch |
| Rotor outside diameter | 11.0 inch |
| Rotor thickness | 1.02 |
| Rotor type | 2-piece, vented, slotted and drilled, zinc plated |
| Rotor material | Iron with aluminum hat |
| Pad type | DR1 or HB100, semi-metallic friction material |
| Axle flange | Ford 9 inch small bearing housing ends |
| Axle flange dimension | 5.75 inch |
| Wheel bolt pattern | 5×4.5/5×4.75 |
| Lug count | 5 lug |
| Minimum wheel diameter | 15.0 inch |
| Template | S125A |
| Emission code | 6 |
| Park brake | No |
Vehicle fitment
Fit depends on the housing: it is made for Ford 9 inch small bearing housing ends with a 5.75 inch axle flange. Confirm your vehicle’s year, model and trim before ordering.
Ford C-clip eliminator housings and GM small pattern housings are different designs and are not covered by this kit. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
Measure the housing flange before ordering, since this kit needs a 5.75 inch flange. Rotors arrive pre-assembled with stainless hardware, and mounting hardware is included. Front rotor, lug nuts and brake hoses are not supplied, so plan for them separately. A dual caliper rear setup is best assembled by someone experienced with drag brake systems.
What’s included
The set includes two sets of S4 calipers with 1.375 inch pistons, pre-assembled two-piece rotors, DR1 or HB100 pads, dust and weather seals, and mounting hardware.
Not included: the front rotor, lug nuts, brake hoses and any park brake.















