Overview
The Baer Brakes 4262319FR is an SS4 Plus Dual Deep Stage rear brake kit for GM small pattern 10/12 bolt bearing on axle housing ends, with a non-flush mount and 3.150 inch bearing. The fire red kit runs four S4 calipers on 11.0 inch 2-piece slotted, drilled rotors and suits heavy, fast cars that may see street use. It is a GM-pattern Deep Stage drag race brake.
The axle flange is GM small pattern 10/12 bolt bearing on axle, a pattern used on Buick, Olds and Pontiac applications. The kit is sized for 15 inch and larger wheels and includes high friction pads for drag race use. The axle flange requirement is 5.75 inch.
Key features
- Four 4-piston S4 calipers with 1.75 inch pistons in fire red powder coat
- Non-flush mount with a 3.150 inch bearing.
- Pistons are hard anodized aluminum, with stainless abutments and noise suppression clips
- 11.0 inch 2-piece slotted, drilled, zinc-plated rotors
- Billet aluminum hats drilled for 5/8 inch wheel studs
- High friction pads for drag race applications
- Pre-assembled rotors with stainless hardware and mounting hardware included
Matching the housing
Non-flush mounts change where the caliper sits relative to the rotor, so the mount style and bearing dimension must line up with the housing end. Measure the housing before planning the install, and write the flange type down alongside the part number. Small pattern housing ends are a specific family, so confirm the axle is the right type before buying anything.
Front and rear rotors on a GM setup should share a sensible thickness and diameter when the brake balance is planned. Drag pads run hot and can glaze, so inspect them after each session. Fire red powder coat resists light chips, but hard contact from road debris can still scratch it, so look over the calipers after rough runs. Check caliper bracket fasteners each time the wheels come off.
- Measure the housing end type and flange first
- Verify the non-flush mount matches before cutting lines
- Keep track of the pad type used at each service
- Inspect caliper brackets for cracks at each service
Specifications
| Brand | Baer Brakes |
|---|---|
| Part number | 4262319FR |
| UPC | 844165049081 |
| Caliper | S4, fixed, 4-piston |
| Calipers included | 4 |
| Caliper color | Fire Red |
| Piston size | 1.75 inch |
| Mount | Non-flush, 3.150 inch bearing |
| Rotor type | 2-piece, vented, slotted and drilled |
| Rotor outside diameter | 11.0 inch |
| Rotor thickness | 1.02 |
| Rotor material | Iron with aluminum hat |
| Minimum wheel diameter | 15.0 inch |
| Bolt pattern | 5×4.50/5×4.75 |
| Lug count | 5 lug |
| Axle flange | GM Small Pattern 10/12 Bolt Bearing on Axle (Buick/Olds/Pontiac) |
| Required axle flange | 5.75 inch |
| Friction material | Semi-metallic |
| Pad FMSI number | DR1 |
| Template | S125A |
| Park brake | Not included |
| Hoses | Not included |
| Country of origin | US |
Vehicle fitment
This GM-pattern kit uses the GM small pattern 10/12 bolt bearing on axle flange, which is found on Buick, Olds and Pontiac applications. Compare your housing end, non-flush mount and 3.150 inch bearing before ordering. Confirm your vehicle’s year, model and trim before ordering.
Confirm your vehicle’s year, model and trim before ordering.
Installation notes
The GM-pattern housing end has to match the flange, the non-flush mount and the 3.150 inch bearing, so measure the housing before starting. Hoses and lug nuts are not supplied. Have a qualified brake shop confirm the fit and final setup of this four-caliper drag race system.
What’s included
Four fire red S4 calipers with 1.75 inch pistons, 11.0 inch 2-piece slotted and drilled rotors with billet aluminum hats, DR1 pad type, dust and weather seals, and mounting hardware.
Not included: brake hoses and lug nuts.















