Overview
The Baer Brakes 4262697FR is a rear drag brake kit for Ford 8.8 inch rear axles, with two 4-piston S4 calipers in Fire Red and two 11 inch slotted, drilled, zinc-plated rotors. It belongs to Baer’s SS4 Plus Deep Stage line, which Baer describes as a drag race system for heavy, fast cars that may see street use.
The kit is sized for wheels 15 inch and larger, and its rotors arrive pre-assembled with stainless hardware. Pad types are DR1 or HB100. No year, model or trim range is given for this part number, so read the fitment section before choosing it.
Key features
- Two 4-piston S4 calipers in Fire Red, with 1.75 inch pistons.
- Hard anodized aluminum pistons, stainless steel abutments and noise suppression clips.
- Two-piece slotted, drilled, zinc-plated rotor with billet aluminum hats drilled for 5/8 inch wheel studs.
- Powder coated finish and dust and weather seals that Baer describes as T compliant.
- Pad types DR1 or HB100, with an FMSI number of DR1.
- Minimum wheel diameter of 15.0 inch.
Choosing the right setup
Rear drag brakes spend most of their life on a short, hard cycle: a full-throttle launch, a hard stop, and a cool-down before the next pass. Each cycle loads the rotors and pads with heat, so the choice between a street compound and a drag compound affects how the setup holds up. Matching pad material to how often the car runs strips is a sensible starting point.
Rear kits also depend on the axle and the lines feeding them. Two calipers on a single axle need balanced pressure from the master cylinder, and the proportioning should be reviewed when the rear system changes. Replacing brake hoses at the same time as the calipers keeps the system consistent and removes an older component from the mix.
- Confirm the master cylinder can supply two calipers
- Replace hoses during the same install
- Bed in new pads before hard runs
- Check rotor hat fasteners after the first session
Specifications
| Brand | Baer Brakes |
|---|---|
| Part number | 4262697FR |
| UPC | 844165050728 |
| Sold as | Kit |
| Caliper | S4, 4-piston, fixed |
| Caliper color | Fire Red |
| Calipers in kit | 2 |
| Piston size | 1.75 inch |
| Rotor outside diameter | 11.0 inch |
| Rotor construction | 2-piece, vented |
| Rotor thickness | 1.02 |
| Rotor material | Iron with aluminum hat |
| Surface | Slotted, drilled and zinc plated |
| Friction material | Semi-metallic |
| Pad FMSI number | DR1 |
| Template | S125A |
| Axle flange | Ford 8.8 inch |
| Axle standoff | 2.5 inch |
| Lug count | 4 lug |
| Wheel bolt pattern | 4×4.25 inch |
| Minimum wheel diameter | 15.0 inch |
| Grade | Performance |
| Park brake | Not included |
| Brake hoses | Not included |
| Lug nuts | Not included |
| Emission code | 6 |
| Country of origin | US |
Vehicle fitment
No year, model or trim range is given for this part number. The axle requirement is a Ford 8.8 inch flange with C-clip eliminators plus a 2.5 inch standoff.
This kit does not work with C-clip axles. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
- The axle needs C-clip eliminators first; this kit is not made for C-clip axles.
- Rotors come pre-assembled with stainless hardware, and mounting hardware is supplied.
- Hoses and lug nuts are not included, so plan to obtain them separately.
A qualified technician should inspect the finished rear brake setup before any drag use.
What’s included
Two S4 calipers in Fire Red, two-piece slotted drilled rotors pre-assembled with stainless hardware, billet aluminum hats, and mounting hardware.
Not included: brake hoses, lug nuts and the park brake.















