Overview
The Baer Brakes 4262258R brings a red SS4 Plus rear brake system to Ford 8.8 Inch C-Clip rear ends with a 2.5 Inch axle standoff. A four-piston S4 caliper works with a 13.0 inch, 2-piece rotor whose billet aluminum hat is pre-assembled, and a 1-piece park brake shoe assembly sits in the backing plate.
The kit uses a 5×4.50 bolt pattern with five lugs and a 17.0 inch minimum wheel diameter. The floating caliper takes DR1-C pads. A red rear kit with an integrated park brake suits this Ford 8.8 Inch axle flange.
Key features
- Red 4-piston S4 caliper with a floating design.
- Powder coated finish on a caliper body of forged or billet aluminum.
- Hard anodized pistons with stainless steel abutments and noise suppression clips.
- Dual seals against dust, weather and pressure.
- 13.0 inch 2-piece rotor with billet aluminum hat, slotted, drilled and zinc plated.
- Rotor hardware is NAS high grade stainless.
- Stainless braided hoses included.
Pads, rotors and wheel clearance
Pads and rotors wear as a pair, so replacing one without the other can leave a new rotor mismatched to an old pad compound. The floating caliper design relies on clean slide pins, so lubricate them with the correct grease whenever the pads come off. Dust boots should be intact to keep grit out of the bore.
Before buying, measure the wheel clearance around the caliper and rotor, since a larger rotor can reduce room behind the spokes. The rear hub and park brake assembly should be inspected at the same time, because corrosion there can affect how the shoes seat against the hat.
- Lubricate caliper slide pins on each pad change
- Check dust boots and seals for cracks
- Bed in new pads before heavy towing
- Confirm wheel clearance around the caliper before mounting
Specifications
| Caliper color | Red |
|---|---|
| Brand | Baer Brakes |
| Part number | 4262258R |
| UPC | 844165028222 |
| Caliper | S4, 4 pistons, floating type |
| Rotor outside diameter | 13.0 inch |
| Rotor thickness | 0.81 |
| Rotor type | 2-piece, vented |
| Rotor material | Iron with aluminum hat |
| Rotor surface | Slotted, drilled, zinc plated |
| Minimum wheel diameter | 17.0 inch |
| Wheel bolt pattern | 5×4.50 |
| Lug count | 5 lug |
| Axle flange | Ford 8.8 Inch |
| Axle standoff | 2.5 Inch |
| Hose material | Steel braided |
| Pad FMSI number | DR1-C |
| Template | S135H |
| Park brake | Included |
| Grade | Performance |
| Country of origin | US |
Vehicle fitment
Fit is set by the Ford 8.8 Inch axle flange with a 2.5 Inch standoff. Wheel styles vary, so check the S135H template against the wheel you plan to use.
Coverage is limited to the 8.8 inch Ford flange with standoff described here. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
Pre-assembled rotor hardware and stainless braided hoses come with the kit. Park brake cables need separate sourcing. Have a qualified technician verify hub and axle fit, bleed the lines, and confirm clearance around the 13.0 inch rotor before the first drive.
What’s included
The red S4 caliper, 2-piece rotor with aluminum hat, park brake shoe assembly, stainless braided hoses and rotor hardware are supplied with this kit.
Not included: you will need to source park brake cables, lug nuts and a front rotor separately.















