Overview
The Baer Brakes S4 front brake system, part 4261379S in silver, is an 11-inch, 2-piece front disc brake kit for 1970 to 1974 Ford and Mercury models that have original drum brake spindles. It covers the Fairlane, Falcon, Maverick, Mustang, Torino, Comet, Cougar, Cyclone and Montego, with the model years for each shown in the fitment section.
The kit pairs a 2-piece, 4-piston S4 caliper made in Phoenix, Arizona, with an 11-inch slotted, drilled, zinc-plated rotor. Billet aluminum hubs come assembled with premium bearings packed in Redline synthetic grease and billet dust caps. Stainless braided hoses and mounting brackets are included. This is the SS4 Plus, a smaller package for 15-inch wheels.
Key features
- 2-piece, 4-piston S4 caliper made in Phoenix, Arizona
- CNC machined from US-sourced forged or billet aluminum
- Hard anodized aluminum pistons with stainless steel abutments
- Dual seals for dust, weather and pressure
- Billet aluminum hubs with premium bearings and billet dust caps
- Rotors pre-assembled with NAS high grade stainless hardware
- 2-piece slotted, drilled, zinc-plated rotor
Converting from drum brakes
Converting a front drum setup to disc changes how the whole brake system works, not only the front wheels. Drum-to-disc kits often pair with a revised master cylinder, brake lines and proportioning hardware. Confirm what a specific car needs before starting, because mismatched components can leave front and rear braking out of balance.
Hubs and bearings need attention during the swap. Grease-packed bearings require the correct torque sequence and a clean spindle surface. Check the spindle for wear and make sure the hub seats fully before the rotor goes on.
The parking brake also changes. Many drum setups used the rear shoes for parking, so confirm how the parking brake will work after the conversion and adjust cables or add a parking solution as needed. Bleed the system fully after any brake line work.
- Review the master cylinder before reinstalling the system
- Check brake lines for wear before reconnecting
- Bleed the hydraulic system after any line work
Specifications
| Brand | Baer Brakes |
|---|---|
| Part number | 4261379S |
| UPC | 844165035565 |
| Caliper | S4, 4-piston, fixed |
| Caliper color | Silver |
| Rotor outside diameter | 11.0 inch |
| Rotor construction | 2-piece, vented |
| Rotor material | Iron with aluminum hat |
| Rotor thickness | 1.02 |
| Rotor surface | Slotted, drilled and zinc plated |
| Pad type | DR1 or HB100 (FMSI DR1) |
| Minimum wheel diameter | 15.0 inch |
| Lug count | 5 lug |
| Wheel bolt pattern | 5×4.50 |
| Wheel stud size | 1/2-20 x 2.25 inch |
| Hose material | Steel braided, DOT approved |
| Template | S162A |
| Axle | Front |
| Grade | Performance |
| Front rotor included | Yes |
| Lug nuts included | No |
| Country of origin | US |
Vehicle fitment
Fits 1970 Ford Fairlane, 1970 Ford Falcon, 1970–1974 Ford Maverick, 1970–1973 Ford Mustang, 1970–1971 Ford Torino, 1971–1974 Mercury Comet, 1970–1973 Mercury Cougar, 1970 Mercury Cyclone and 1970–1971 Mercury Montego, all with original drum brake spindles.
Model years outside these ranges, such as a 1974 Mustang or a 1972 Torino, are not covered. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
This kit is listed with the drum brake spindle note, so the vehicle must have original drum brake spindles to match. Template S162A is the reference for checking wheel clearance over the 11-inch rotor. Hubs come assembled with bearings packed in Redline synthetic grease, and the rotors come pre-assembled with stainless hardware. Brake work should be done by a qualified technician.
What’s included
Front S4 brake system with 4-piston calipers, 11-inch 2-piece rotors, billet aluminum hubs, stainless braided hoses, mounting brackets and hardware.
Not included: Lug nuts.














