Overview
The Artec Industries JK6033 is a front Dana 60 swap kit for 2007–2016 Jeep Wrangler (JK) 2-door and 4-door models. It includes an adjustable truss upper link mount, and it is built for Ford Dana 60 axles from model years 85–97. Superduty axles from 1999–2004 are also named for this kit.
The truss and bracket system is built from 1/4 in. thick mild steel, with interlocked 1/4 in. gussets. The brackets are jigged into the truss, so the control arm, shock, anti-sway bar, track bar and coil spring locations are set when the truss is assembled.
Key features
- 1/4 in. thick mild steel truss and brackets
- Interlocked 1/4 in. gussets for truss strength
- Adjustable truss upper link mount
- Track bar mount with four locations for aftermarket lifts
Planning a front axle swap
A front axle swap changes more than the axle itself. The truss and brackets set the locations for the control arms, shocks, anti-sway bar, track bar and coil springs, so the front geometry is fixed by the kit rather than the factory mounts. Before buying, decide how much lift and tire size you plan to run, because larger tires and a taller stance change steering feel, driveshaft angles and brake line length. New wheels are usually bought at the same time, since a different axle bolt pattern requires them.
After the new axle is installed, check the steering linkage, ball joints and tie rod ends for play, and inspect the bumpstops for clearance through full travel. Bushings on the truss and control arms should be looked at after the first few trail runs, and fasteners should be re-torqued at each oil change. A front differential needs fluid checks like any other axle, and a leak at the pinion or axle seals is worth catching early.
- Track bar and steering geometry checked after installation
- Brake lines routed clear of moving parts and suspension travel
- Driveshaft angles measured once the lift is in place
Specifications
| Brand | Artec Industries |
|---|---|
| Part number | JK6033 |
| UPC | 816791021908 |
| Axle | Front Dana 60 |
| Axle named in title | Superduty, 1999–2004 |
| Upper link mount | Adjustable truss mount (per title) |
| Axle tube check | 3.0 in. driver side, 24.5 in. passenger side |
| Wheel bolt pattern | Dana 60 does not match the JK 5-lug pattern |
Vehicle fitment
The kit fits 2007–2016 Jeep Wrangler (JK) 2-door and 4-door models, including the 70th Anniversary, Rubicon, Sahara, Sport, Sport S and X trims and their Unlimited versions.
The Ford Dana 60 covered by this kit is from model years 85–91.5 (kingpin) and 92–97 (ball joint). Superduty axles from newer model years are still in development. Because the kit is named for 1999–2004 Superduty axles, confirm the axle year before ordering.
Confirm your vehicle’s year, model and trim before ordering.
Installation notes
A Dana 60 axle is required, with 3.0 in. of driver side axle tube and 24.5 in. of passenger side axle tube.
Expect new wheels, since Dana 60 axles do not match the factory JK 5-lug bolt pattern.
Lower control arms may need modification because the lower control arm brackets sit wider than factory, and adjustable upper control arms may be needed because those brackets sit higher.
Brake and steering components are not included. Bumpstop extensions and a new track bar will likely be needed, and kingpin axles are the usual choice for this kit.
What’s included
The truss, brackets and control arm, shock, anti-sway bar, track bar and coil spring mounts, with the adjustable truss upper link mount.
Not included: Brake and steering components, and new wheels for the Dana 60 bolt pattern.











