Select your vehicle

Vengeance Bumper with Pre-Runner Bumper in Bare Steel

Fab Fours

Shop Ford F-150 Front Bumpers on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Fab Fours Vengeance front bumper with pre-runner guard for the 2017-2018 Ford F-150 Raptor
  • Bare steel, 11 ga. U.S. steel construction, bolt-on with brackets to the frame
  • Center mount for a 20 inch LED light bar and side mounts for two 2×2 Dually lights; lights not included
  • Weighs 65 lb without the guard and 75 lb with the pre-runner guard

Description

Overview

The Fab Fours FF17-D4352-B is a Vengeance front bumper with a pre-runner guard in bare steel for the 2017-2018 Ford F-150 Raptor. The fit is high and tight to the vehicle’s contours, and it is a complete bolt-on unit with brackets that tie directly to the frame.

The Vengeance Series is a line of lightweight steel bumpers. The design retains factory technology such as Adaptive Cruise Control and Park Assist when the optional relocation bracket is used. The bumper has a center cutout for a 20 inch LED light bar and lower cutouts for airflow.

Key features

  • Bare steel, 11 ga. U.S. steel construction
  • High and tight fit to the contours of the vehicle
  • Complete bolt-on bumper with provided brackets that tie directly to the frame
  • Center mount for a Rigid Industries 20 inch LED light bar (not included)
  • Mounting options on each side for two 2×2 Dually lights (not included)
  • Lower cutout for airflow
  • Optional relocation bracket M3850-1 to retain factory technology features
  • Optional mesh inserts for the center cutout and side openings
  • Made in the USA

Fitting a bare steel bumper

Bare steel bumpers need a little more attention than powder-coated ones. Bare metal can start to rust at cut edges, bolt holes and welds, so consider a coat of primer or a rust-inhibiting sealer on any exposed areas during installation. Clean the surfaces well before painting, and apply a finish that suits the steel and your climate.

Front end weight matters for steering, braking and suspension load. A heavier pre-runner guard adds mass ahead of the front axle, so think about how the truck will handle on road and trail, and whether the load will change tire wear. Check the stock suspension and the brakes after the first drives with the bumper fitted.

Adding a bumper with a center light mount and side mounts raises the question of sensor placement. If the truck has adaptive cruise control or park assist, check sensor alignment after fitting and confirm whether the relocation bracket is needed. Recheck the frame brackets after rough roads, and inspect the weld and bolt areas for early rust.

  • Prime cut edges and bolt holes
  • Check suspension and brakes after first drives
  • Re-check frame bolts after rough roads

Specifications

Brand Fab Fours
Part number FF17-D4352-B
UPC 5810114657
Product type Front bumper with pre-runner guard
Series Vengeance
Position Front
Material Steel, 11 ga. U.S. steel
Finish Bare steel
Weight without guard 65 lbs
Weight with pre-runner guard 75 lbs
Light bar mount Center, for a 20 inch LED light bar
Side light mounts Two 2×2 Dually lights each side
Optional center mesh insert M2450-1
Optional side mesh insert M3950-1
Optional relocation bracket M3850-1
Origin stated in source Made in the USA
Fit type Direct fit

Vehicle fitment

This bumper fits the 2017-2018 Ford F-150 Raptor.

This bumper is for 2017-2018 only. Other Raptor years and other F-150 trims are not covered. The optional relocation bracket is needed to retain factory technology features. Confirm your vehicle’s year, model and trim before ordering.

Installation notes

Bumpers add significant weight to the front or rear of a vehicle, so use a helper or lifting equipment during installation. Use all of the supplied hardware, follow the fastener sequence in the fitting steps, and tighten each bolt fully before moving on.

Re-check the mounting bolts after the first miles of driving. Confirm clearance around sensors, lighting and the winch or recovery equipment you plan to use, and check local regulations on bumper height and lighting.

If the vehicle has Adaptive Cruise Control or Park Assist, confirm sensor placement and the need for the optional relocation bracket before installation.

What’s included

The Vengeance front bumper with pre-runner guard comes with the brackets that tie it to the frame.

Not included: Lights and the light bar are not included. The optional mesh inserts (M2450-1 for the center and M3950-1 for the sides) and the relocation bracket (M3850-1) are separate parts.

SKU: FFIFF17-D4352-B Category:

Specification

Shipping weight 150.00 lbs
Package dimensions 84.00 × 30.00 × 26.00 in
brands

Fitment

VehicleYearsTrims
Ford F-1502017–2018Raptor

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

What vehicle does the Fab Fours FF17-D4352-B fit?

It fits the 2017-2018 Ford F-150 Raptor. The fit is high and tight to the vehicle's contours, and the bumper is a bolt-on unit with brackets tied to the frame.

Does the Fab Fours Vengeance bumper work with Adaptive Cruise Control?

The bumper retains factory technology such as Adaptive Cruise Control and Park Assist when the optional relocation bracket M3850-1 is used. That bracket is a separate part and is not in the box.

Are lights included with the FF17-D4352-B?

No. The bumper has a center mount for a 20 inch LED light bar and side mounts for two 2x2 Dually lights, but the lights are not included.

How much does the Vengeance bumper weigh?

The bumper weighs 65 lb without a guard and 75 lb with the pre-runner guard. This product includes the pre-runner guard, so the 75 lb figure applies.

How should I maintain the finish on a bare steel bumper?

Wash the bumper regularly and dry it to keep moisture off the bare metal. Look for surface rust at the edges and bolt holes, and treat it early with a wire brush and a rust-inhibiting primer. Reapply a protective coat after repairs so the steel stays protected through the seasons.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Ford F-150 Front Bumpers on Amazon