Select your vehicle
-13%

Superchips LIT E-Series 20 Single Row LED Combo Light Bar with Power Switch – 72021

Superchips

Shop Superchips Light Bars on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • 20-inch single-row LED combo light bar with a power switch kit
  • Designed to run from the accessory port on a TrailDash or TrailDash2 monitor
  • Included relay harness connects to the battery for plug-and-play wiring
  • The switch can also control a second 12-volt accessory

Description

Overview

The Superchips LIT E-Series 20 Single Row LED Combo Light Bar with Power Switch, part number SCI72021, is a 20-inch single-row LED light bar with a combo beam and a power switch kit. The kit is built to pair with the TrailDash or TrailDash2 monitor, so the bar is switched from the monitor’s accessory port instead of a switch panel cut into the factory dash.

The kit includes a relay harness that runs from the power switch to the battery, and the setup is designed as a plug-and-play connection that removes much of the guesswork from wiring the bar. The switch can also control a second circuit, so another LIT light bar, an air compressor or a different 12-volt accessory can run from the same setup.

Key features

  • 20-inch single-row LED light bar with combo beam
  • Power switch accessory that connects to a TrailDash or TrailDash2 monitor
  • Included relay harness for the battery connection
  • Second circuit for another 12-volt accessory
  • No drilling into the factory dash for a switch panel

Wiring and fusing basics

Wiring a light bar is mostly about protecting the circuit. A relay keeps the high current away from the switch, and a properly sized fuse close to the battery protects the harness if the bar or its wiring is damaged. Run the cable along existing body or frame routes, secure it with clips, and keep it away from sharp edges, exhaust heat and moving suspension parts. Water and mud get into poorly sealed connectors, so apply dielectric grease and use any weatherproof caps that come with the kit.

Mounting height and aim matter as much as the wiring. A bar mounted high across the front throws light farther down the trail, while a lower mount on a bumper or bar lights the near area and the ruts beside the tires. Before drilling, check clearance for the hood, the windshield wipers and any winch or bumper parts already installed. Measure the bracket position twice and check that the bar sits level so the beam is not pointed at the sky.

  • Check the fuse rating against the bar’s current draw before connecting power
  • Inspect connectors for corrosion after each season of wet trail use
  • Re-tighten mounting bolts after the first few runs

Specifications

Brand Superchips
Part number SCI72021
Product line LIT E-Series single row with power switch
Light type LED light bar, sold as a single bar
Size 20 inch
Beam pattern Combo
Bulb type LED
Control Power switch for the TrailDash or TrailDash2 accessory port
Finish Black

Vehicle fitment

The light bar and power switch are a universal fit and are not made for one specific Jeep or vehicle. Compatibility depends on the TrailDash or TrailDash2 monitor, because the power switch uses that monitor’s accessory port.

Confirm that your monitor is a TrailDash or TrailDash2 and check its accessory port layout before fitting.

Installation notes

Connect the power switch to the monitor’s accessory port and run the included relay harness to the battery. The kit is set up for a plug-and-play connection, but the harness still needs a clean, secure route and fusing as the wiring instructions direct.

What’s included

The kit includes the 20-inch light bar, the power switch accessory and the relay harness for the battery. A TrailDash or TrailDash2 monitor is required for the switch’s accessory port and must be purchased separately.

Not included: TrailDash or TrailDash2 monitor.

Questions & Answers

Does the Superchips SCI72021 work with a TrailDash monitor?

Yes. The power switch connects to the accessory port on a TrailDash or TrailDash2 monitor, so the 20-inch bar can be controlled from the monitor, with a relay harness running to the battery.

Does the kit need drilling into the dash?

No. The power switch accessory avoids drilling into the factory dash for a switch panel, and the included relay harness runs to the battery.

Can the power switch run anything besides the light bar?

Yes. The switch can control a second circuit, so another light bar, an air compressor or any 12-volt accessory can be added to the same setup.

How should a light bar be cared for?

Wipe the lens with a soft cloth and clean water, and avoid abrasive pads that can scratch the surface over time. Check the mounting bolts, wire insulation and connector seals periodically, especially after rough trail use or heavy rain. Replace any cracked lens or damaged cable before it lets water reach the electrical connections.

Can a second light be added to the same switch?

A second circuit can be added only if the total current stays within what the relay harness and the wiring can handle. Add up the draw of each accessory, then confirm the fuse and wire gauge can carry the combined load. If the load is close to the limit, use a separate relay for the added light.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Superchips Light Bars on Amazon