Overview
The SPOD Modular SourceLT LED 6-Switch Panel with blue LEDs, part number PODSL-MOD-84-B, is a solid-state 6-circuit control system for powering and controlling 12VDC accessories through one cable into the cab. It is universal fit and not designed around a single vehicle.
The module is small, so it can go in many locations, and SPOD says no cutting, fishing wires into the cab or tapping the vehicle’s electrical system is needed. Six dual lit LED switches come installed and pre-wired on the panel, and the sPOD Mobile App handles switch programming. Bluetooth features require an existing sPOD system.
Key features
- 6 circuits rated at 30 amps at 12.5 VDC per circuit, operating on 12VDC
- Six dual lit LED switches installed and pre-wired, with a controlled lower pilot light (push button)
- Carling Technologies Contura switches certified to IP66/68 for marine and harsh environments
- 12-position terminal block for attaching accessories
- 10 foot control cable for plug-n-play connection to the switch controller
- Integrated low voltage cutoff (LVCO) battery protection with optional override
- Self-healing fault protection circuits from 1.5 to 30amps, with current-sensing MOSFETs controlled by a microprocessor (no fuses and no relays)
- 50amp auto-resetting circuit breaker
- Aluminum panels formed, welded and powder coated, with wires in high-temp abrasion resistant nylon braided sleeving
- Automatic safe system shutdown when the panel is unplugged, and sPOD Mobile App programming for dimming, strobe, flash, momentary, switch linking and on-road and off-road modes
Control cable and power routing
The control cable runs from the panel to the switch controller, so route it along existing harness paths where possible. Keep it away from exhaust heat, moving suspension parts and sharp body edges. Secure it with clips at regular intervals so it does not sag or rub, and leave a small service loop at the panel so the connector can be unplugged without strain.
The panel’s lid and base seal against the weather, but water still finds its way into poorly routed wiring. Use drip loops where cables leave the panel and seal any cut or pierced openings. Before using a new panel on rough trails, check that every switch seats firmly and that the connector is fully engaged.
- Route the control cable away from exhaust and moving parts
- Leave a service loop at the panel connector
- Check switch seating after the first few trail outings
Specifications
| Brand | SPOD |
|---|---|
| Part number | PODSL-MOD-84-B |
| Model | SL-MOD-84-B |
| Product | Modular SourceLT LED 6-Switch Panel, blue |
| Circuits | 6, rated at 30 amps at 12.5 VDC per circuit |
| Operating voltage | 12VDC |
| Switches | Six dual lit LED switches, Carling Technologies Contura, IP66/68 |
| Terminal block | 12-position |
| Control cable | 10 foot |
| Circuit breaker | 50amp auto-resetting |
| Fault protection | Self-healing, 1.5 to 30amps |
| Battery cables | |
| Panel | Aluminum, formed, welded and powder coated |
| Base | Powder coated steel base with built in hardware |
| Lid | Aluminum, thumb screw fastening, silicone gasket for weatherproofing |
| Bluetooth | Bluetooth 4.0 compatible; Android 8.0 Oreo (API 26) or later; iOS 11 or newer, iPhone 7s or newer, iPad 2 or newer, iPad mini |
| Mounting | Universal, with vehicle specific options |
| Fitment | Universal Fit |
Vehicle fitment
The SourceLT panel is universal fit and not tied to one make, model or year. Vehicle specific mounting options exist, but no vehicle is named for them.
Confirm your vehicle’s year, model and trim before ordering. Choose a mounting option that matches the vehicle you install it in.
Installation notes
The panel uses a 10 foot control cable that plugs into the switch controller, so map the route before mounting. Measure the battery cable route before routing and confirm the cable length for your installation. Keep every accessory’s draw inside the 30 amp per circuit rating when you wire the panel.
What’s included
Included: six installed and pre-wired dual lit LED switches, a 10 foot control cable, battery cables and a power distribution module.
Not included: Air pressure gauge, custom laser-etched rockers (sold separately), and an existing sPOD system, which the module must have to work.










