Select your vehicle

SPOD BantamX LED 8-Switch Panel (Blue) – BX-0708-JK-B

SPOD

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • SPOD BantamX LED 8-switch panel, blue, part PODBX-0708-JK-B
  • Fits 2007–2008 Jeep Wrangler (JK) Rubicon, Sahara and X trims
  • Eight circuits rated at 30 amps at 12.5 VDC each
  • Eight dual lit blue LED switches, installed and pre-wired

Description

Overview

The SPOD BantamX LED 8-Switch Panel (Blue), part PODBX-0708-JK-B, is an overhead switch panel with eight dual lit blue LED switches for running 12 or 24 volt accessories through the BantamX control system. It fits the 2007–2008 Jeep Wrangler (JK).

The BantamX connects to the panel through a single Ethernet cable, which keeps the wiring tidy. Each of its eight circuits is rated at 30 amps at 12.5 VDC. Switches can be programmed for dimming, strobe, flash, momentary and switch linking through the free sPOD Mobile App, while advanced options such as circuit timers and switch lockout need the separate Pro-Series App.

Key features

  • Eight dual lit blue LED switches, installed and pre-wired
  • Eight circuits rated at 30 amps at 12.5 VDC each, expandable
  • Operates on 12VDC or 24VDC
  • Integrated low voltage cutoff battery protection with optional override
  • Built-in Bluetooth for remote control
  • Carling Technologies Contura switches certified to IP66/68
  • Aluminum panels formed, welded and powder coated

Overhead mounting basics

An overhead panel sits where the driver and passengers reach it, so position matters as much as the wiring. Pick a spot that clears the headliner, grab handles and any airbag area, and check that you can reach every switch while seated. Mark the mounting points and test the cable route before drilling or fastening anything.

Once the panel is in place, keep the Ethernet run clear of sharp edges, hot components and moving parts. Leave a small service loop so the controller connection can be checked without strain. Label each switch after the accessories are wired so the lit switches are easy to identify at night. Good cable management also makes later service easier.

  • Check overhead clearance before choosing the final spot
  • Route the Ethernet cable with clips rather than loose hanging
  • Keep accessory wiring separate from the control cable

Specifications

Brand SPOD
Part number PODBX-0708-JK-B
Mounting location Overhead
Switches Eight dual lit blue LED switches
Switch brand Carling Technologies Contura
Switch rating IP66/68 certified (marine/harsh environment)
Circuits 8, expandable; 30 amps at 12.5 VDC per circuit
Operating voltage 12VDC or 24VDC
Accessory terminal block 16-position
Input terminal block 8-position
Controller ports 2 RJ45 for Ethernet cables
Ethernet cable 10 foot CAT-6, extendable up to 25 feet
Circuit breaker 50 amp auto-resetting
Air pressure gauge Not included
Fitment 2007–2008 Jeep Wrangler (JK)

Vehicle fitment

It fits the 2007–2008 Jeep Wrangler (JK) in the Rubicon, Sahara, Unlimited Rubicon, Unlimited Sahara, Unlimited X and X trims.

Fit is established for 2007–2008 Wrangler JK models only, so verify year, model and trim before buying.

Installation notes

The panel arrives installed and pre-wired, so the work centers on overhead mounting and running the 10 foot Ethernet cable to a BantamX controller port. Accessory wiring connects at the 16-position terminal block.

What’s included

Eight dual lit blue LED switches installed and pre-wired in an aluminum panel, plus a 10 foot CAT-6 Ethernet cable.

Not included: external controllers such as third-party switches, computers, Arduino or Raspberry Pi boards, and the Pro-Series App features.

SKU: PODBX-0708-JK-B Categories: , ,

Fitment

VehicleYearsTrims
Jeep Wrangler (JK)2007–2008Rubicon (2-Door), Sahara (2-Door), Unlimited Rubicon (4-Door), Unlimited Sahara (4-Door), Unlimited X (4-Door), X (2-Door)

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Does the SPOD BantamX 8-switch panel fit a 2007 Jeep Wrangler JK?

Yes. It fits 2007–2008 Jeep Wrangler (JK) models, including 2-door Rubicon and Sahara and Unlimited Rubicon, Unlimited Sahara, Unlimited X and X trims.

Does this panel fit a 2010 Jeep Wrangler?

No. It fits 2007–2008 models only, so 2009 and later Wranglers are not covered. Confirm your year and model before choosing this panel.

How many circuits does the BantamX system run, and at what amperage?

The BantamX runs eight circuits, each rated at 30 amps at 12.5 VDC, and it operates on 12 or 24 volts. The system is expandable, and up to four units can be daisy chained under one touchscreen.

What should I check before mounting an overhead panel?

Check that the spot clears the headliner, grab handles and any airbag area, and that the controller and cable reach it without strain. Measure the panel footprint first and confirm you can reach every switch while seated.

How do I maintain the switch panel?

Wipe the panel with a mild cleaner and check the LED switches for dimming or sticking. Inspect the Ethernet connections and terminal blocks for corrosion or loose wires, especially after trail use.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon