Select your vehicle
-13%

Smittybilt XRC Gen2 Rear Armor – 76885

Smittybilt

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Rear XRC Gen2 armor (fender flares) for the 2007–2018 Wrangler (JK)
  • Also fits one 2018 Wrangler (JL) Unlimited Moab 4-door
  • Black powdercoat, can be painted to match
  • No cutting or drilling, part number 76885

Description

Overview

The Smittybilt XRC Gen2 Rear Armor, part number 76885 (S/B76885), is a pair of black powder coated bolt-on rear fender flares for the 2007–2018 Jeep Wrangler (JK).

The XRC Gen2 rear armor is a bolt-on rear flare for the JK, built for protection and tire clearance in tough conditions. It arrives powder coated for immediate use or can be painted to match the vehicle. The streamlined shape is meant to help increase suspension articulation while keeping a street-able look. The rear pieces widen clearance at the rear wheel openings and replace the stock rear fender flares.

Key features

  • Bolt-on rear fender flares for the Wrangler JK
  • Engineered for protection and clearance
  • Black powder coat, ready to use or paintable to match the vehicle
  • Streamlined design intended to help increase suspension articulation
  • Retains a street-able look
  • No cutting or drilling required

Rear clearance and upkeep

The rear flares sit over the tires behind the rear axle, where mud and water spray off the back wheels. A flare that clears the tire at rest may still rub under load or at full droop, so consider the tire width you run and any rear suspension changes before you install. Trim pieces and bumpers around the flare should be checked as well, since a shift in one part can affect how the other sits.

Rear flares see a lot of rock and water, so the lower edges take the most wear. Wash the powder coat after trail use, touch up chips quickly, and look for dirt trapped behind the mounts, which can hold moisture against the metal. Recheck the fasteners after the first few outings, because bolts can back off as the body flexes.

  • Check clearance at full suspension compression
  • Clean debris from behind the mounting points
  • Touch up chips on the lower edge promptly
  • Retighten fasteners after early trail runs

Specifications

Brand Smittybilt
Part number S/B76885
Product type Rear fender (XRC Gen2 armor)
Finish Black powdercoat
Location and position Rear
Fitment type Direct fit
Installation type No cutting or drilling required

Vehicle fitment

Fitment covers the 2007–2018 Jeep Wrangler (JK) and one 2018 Jeep Wrangler (JL), Unlimited Moab 4-door.

Confirm fit for your vehicle’s year, model and trim before ordering. It covers the JK from 2007 to 2018 and one 2018 JL Unlimited Moab 4-door.

Installation notes

Smittybilt says no cutting or drilling is required, so the flares install as a bolt-on.

What’s included

Check the piece count and hardware against your installation before starting.

Fitment

VehicleYearsTrims
Jeep Wrangler (JK)2007–2018Unlimited 70th Anniversary (4-Door), Unlimited 75th Anniversary (4-Door), Unlimited Rubicon (4-Door), Unlimited Sahara (4-Door), Unlimited Sport (4-Door), Unlimited Sport S (4-Door), Unlimited X (4-Door)
Jeep Wrangler (JL)2018Unlimited Moab (4-Door)

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

What Jeeps does the Smittybilt XRC Gen2 rear armor 76885 fit?

Part number 76885 is the rear XRC Gen2 armor for the 2007–2018 Jeep Wrangler (JK) and one 2018 Jeep Wrangler (JL) Unlimited Moab 4-door. Verify your vehicle's year, model and trim before you order.

Can the XRC Gen2 rear armor be painted?

Yes. Smittybilt says each XRC GEN2 piece is powder coated for immediate use or can be painted to match the vehicle.

Does the Smittybilt 76885 rear armor require drilling?

No. The XRC Gen2 rear armor is a bolt-on rear flare for the JK, and installation does not require cutting or drilling.

Is 76885 the front or rear XRC Gen2 armor?

It is the rear armor. Smittybilt gives both the location and the position as rear, and the front piece has a different part number.

Can rear flares be painted after installation?

Yes. The pieces can be painted to match the vehicle. Clean the surface thoroughly, scuff the powder coat lightly, and use a primer suited to the material so the paint bonds. Mask the mounting areas to keep the fasteners and threads clear.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon