Select your vehicle
-13%

Smittybilt Sure Step 3″ Diameter Side Bars (Textured Black) – JN460-S2T

Smittybilt

Shop Jeep Wrangler TJ Nerf Steps on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Fits the 1997–2006 Jeep Wrangler (TJ)
  • 3″ diameter textured black powder-coated side bars, wheel to wheel
  • No-drill installation with an eight-point frame mount
  • Pair with all hardware included

Description

Overview

The Smittybilt Sure Step 3″ Diameter Side Bars in textured black, part number S/BJN460-S2T (model JN460-S2T), are wheel-to-wheel side steps for the 1997–2006 Jeep Wrangler (TJ). Side bars, also called nerf bars or side steps, give a place to step when getting into the Jeep.

Each step pad is secured with 5 pins in a squashed step, so there is no exposed metal to rust. The step pads are non-slip polyester. The eight-point frame mount gives a rugged, rigid attachment, and the installation is no-drill. The 3-inch tube has a black powder coat finish.

Key features

  • 3″ diameter tube with a textured black powder coat finish
  • No-drill installation
  • Rugged eight-point frame mount for strength and rigidity
  • Heavy-duty welded design
  • Non-slip polyester step pads secured with 5 pins in a squashed step
  • Oversize bolt attachment, which Smittybilt says prevents tube step bounce
  • All installation hardware included
  • Supplied as a pair

Textured black and trail wear

Powder coat is a tough finish, but it can chip where stones hit the tube, and a chip exposes steel that can start to rust. Inspect the finish after each trail season, and touch up small damage with a metal-safe paint before corrosion spreads under the coating.

Side bars on a Wrangler take the load of people climbing in, so the frame mounts matter as much as the bar itself. Look for loose hardware, cracked brackets or bent tubes after a hard hit. Keeping mounting points clean makes it easier to spot early wear.

Wheel-to-wheel bars sit low and can catch branches or ruts. Consider how your ground clearance and approach angle change with the bars installed, and plan rock sections accordingly. Pads should be checked for grip, especially after mud, and cleaned if they start to slip under boots.

Specifications

Brand Smittybilt
Part number S/BJN460-S2T
Product type Side bars (side steps)
Tube diameter 3″
Length Wheel to wheel
Finish Black powder coat (textured black)
Step pads Non-slip polyester
Mounting Eight-point frame mount, no drilling
Quantity Pair
Fit type Direct fit

Vehicle fitment

It fits the 1997–2006 Jeep Wrangler (TJ) in 65th Anniversary Edition, Rubicon, SE, Sahara, Sport and X trims.

The bars run wheel to wheel, between the front and rear wheel openings. Measure your vehicle’s wheel openings to confirm fit before installing.

These side bars fit the Wrangler TJ only, not the YJ, LJ, JK or JL. Confirm fit for your vehicle’s year, model and trim before ordering.

Installation notes

Tighten every fastener to the values the package gives, working in the order it sets out. Recheck the hardware after the first few miles, and inspect it again after rough off-road use. If installing the bars is not something you are comfortable doing, have a qualified shop fit them.

Side steps are loaded by people stepping on them, so after installation check that every frame mount bolt is tight, that the bars are level and firmly attached, and re-check them after the first miles of driving.

What’s included

A pair of side bars with all installation hardware.

SKU: S/BJN460-S2T Categories: , ,

Fitment

VehicleYearsTrims
Jeep Wrangler (TJ)1997–200665th Anniversary Edition, Rubicon, SE, Sahara, Sport, X

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

What Jeep do the Smittybilt JN460-S2T side bars fit?

These fit 1997–2006 Jeep Wrangler (TJ) trims 65th Anniversary Edition, Rubicon, SE, Sahara, Sport and X. Sizing runs wheel to wheel, so confirm your trim before ordering.

Do the Smittybilt Sure Step bars require drilling?

No. Smittybilt lists no-drill installation, using a rugged eight-point frame mount. All installation hardware is included with the pair, so no separate hardware kit is listed.

What finish do the S/BJN460-S2T side bars have?

They have a black powder coat finish on a 3-inch diameter tube. The step pads are non-slip polyester, and the bars come as a pair with all installation hardware.

How should I clean the textured black finish?

Rinse the bars with water after muddy trips and use a mild soap on the tube. Avoid harsh solvents that can dull or lift the coating. Dry the steel and check for chips, since moisture trapped under damaged paint can start rust.

Do the side bars affect ground clearance?

Yes, side bars sit low, so they can reduce clearance at the rocker area. Check the height against the terrain you drive, and avoid tight rock sections if the bars sit close to the trail. Recheck clearance any time the suspension or tires change.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Jeep Wrangler TJ Nerf Steps on Amazon