Select your vehicle

Skyjacker 2.5 Inch Rock Ready Double Wrap Rear Leaf Spring – YJ25RS

Skyjacker

$262.37In stock
Buy on Amazon

See similar parts on Amazon

Price and availability as of Nov 18, 2026 3:20 PM MST, from Amazon.com, and subject to change. The Amazon listing has the current details.

Check out with your Amazon account. Amazon handles delivery and returns.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Skyjacker YJ25RS 2.5 inch rear double wrap leaf spring
  • Direct fit for 1987–1995 Jeep Wrangler (YJ) per the manufacturer fitment list
  • Single rear spring, lift height range 0 to 4.99 inches
  • American steel leaves, shot peened, bolt-style clips
  • Bushings not included; bushing part number SKYSE45YJ

Description

Overview

The Skyjacker YJ25RS is a 2.5 inch rock ready double wrap rear leaf spring for the 1987–1995 Jeep Wrangler (YJ). It is a single rear spring from Skyjacker’s Softride line, designed to deliver off-road handling and wheel travel while keeping street ride quality smooth. Skyjacker presents the Softride design as a middle ground between hard off-road performance and everyday comfort.

Softride leaves are made from American steel, and each leaf is shot peened with hard steel pellets at high velocity. The peening compresses the steel surface and raises tensile strength. Without shot peening, the wheel travel and ride quality this spring is built for would cost spring life.

Key features

  • Made from American steel, with each leaf shot peened for added tensile strength
  • Bolt-style spring clips, which Skyjacker says eliminate the binding and friction of cinch-style clips
  • Leaves taper across their full width, adding flex at the leaf ends
  • The taper spreads load over a larger area and reduces one leaf digging into the leaf above it
  • Rock ready double wrap design, supplied as a single rear spring
  • Lift height range of 0 to 4.99 inches, with direct fit

Rear spring lift and clearance

A rear double wrap spring changes the height of the axle and the clearance under the rear of the Jeep. Tires, fender trim and brake lines should be checked for rubbing at full compression, since a lift can move those parts closer together than before. A test drive over a few bumps is a simple way to spot a problem early.

Because this spring uses bolt-style clips, the clip hardware and leaf alignment should be checked during the install. Shackles and bushings can wear alongside the spring, and replacing them at the same time keeps the rear end working as intended. Rear springs carry significant load, so tighten the hardware in stages and recheck it after the first drive.

  • Check tire and brake line clearance at full compression
  • Inspect clips and leaf alignment during installation
  • Replace worn shackles and bushings together
  • Recheck torque after the first drive

Specifications

Brand Skyjacker
Part number YJ25RS
UPC 803696169897
Product type Double wrap leaf spring, Softride design
Position Rear
Spring quantity Single spring
Material American steel, shot peened leaves
Clip style Bolt style
Bushings included No, bushings not included
Bushing part number SKYSE45YJ (needed separately)
Lift height range 0 to 4.99 inches
Intended setup 2.5 inch lifted springs
Fitment type Direct fit

Vehicle fitment

It is a direct fit for the 1987–1995 Jeep Wrangler (YJ), covering the Base, Islander, Laredo, Renegade, Rio Grande, S, SE, Sahara and Sport trims.

Its fitment is limited to the 1987–1995 Wrangler YJ, so the TJ, LJ and JK generations are outside it. Compare your year and trim against that range before ordering.

Installation notes

The bushings are not included, so a bushing set has to be obtained before the spring goes in. Skyjacker lists bushing part number SKYSE45YJ. The spring uses bolt-style clips, so check the clip hardware during installation. Rear springs carry axle weight, so support the axle securely before removing the old spring.

What’s included

One rear leaf spring, supplied as a single spring.

Not included: Spring bushings. Skyjacker lists bushing part number SKYSE45YJ for them.

SKU: SKYYJ25RS Category:

Specification

Shipping weight 36.00 lbs
Package dimensions 45.00 × 2.50 × 2.50 in
brands

Fitment

VehicleYearsTrims
Jeep Wrangler (YJ)1987–1995Base, Islander, Laredo, Renegade, Rio Grande, S, SE, Sahara, Sport

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Will the Skyjacker YJ25RS fit my Jeep Wrangler?

Yes, if your vehicle is a 1987–1995 Jeep Wrangler YJ. It is a direct fit for that generation across the Base, Islander, Laredo, Renegade, Rio Grande, S, SE, Sahara and Sport trims. Compare your trim with that list before ordering.

Does the YJ25RS include spring bushings?

No. Bushings are not included with this rear spring. Skyjacker lists bushing part number SKYSE45YJ for the bushings, and they need to be on hand before installation because this spring comes without them.

Is the YJ25RS a front or rear spring?

It is a rear spring, sold as a single unit with a lift height range of 0 to 4.99 inches. The 2.5 inch rock ready design is intended for a 2.5 inch lift setup, so match it to that lift before installing.

Can a rear spring be swapped without changing the shocks?

It can be, but the shocks should be checked. A new spring changes ride height, so the shock length and mounting angle may no longer suit the setup. Inspecting shocks when the spring goes in helps avoid bottoming out and uneven wear.

Ready to order?

Order this part on Amazon and check out with your Amazon account. Amazon handles delivery and returns.

Buy on Amazon