Select your vehicle

Omix-ADA Front Drive Shaft – 16950.06

Omix-Ada

$690.63Currently unavailable
Buy on Amazon

See similar parts on Amazon

Price and availability as of Nov 18, 2026 1:10 AM MST, from Amazon.com, and subject to change. The Amazon listing has the current details.

Check out with your Amazon account. Amazon handles delivery and returns.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Fits the 1982–1983 CJ5 and 1982–1986 CJ7
  • Front drive shaft, stock length, non-CV
  • No slip yoke eliminator required
  • Limited five year warranty

Description

Overview

The Omix-ADA 16950.06 is a stock-length, non-CV front drive shaft for the Jeep CJ5 (1982–1983) and CJ7 (1982–1986), built as a direct OE replacement.

Omix-ADA builds its direct OE replacement Jeep parts to the original specifications. This front drive shaft is non-CV with stock length and does not require a slip yoke eliminator. It comes with a limited five year warranty. A front drive shaft carries power from the transfer case to the front axle on a four-wheel-drive vehicle, so it is the part to check when a worn or damaged original needs replacing on a CJ.

Key features

  • Front drive shaft, direct OE replacement
  • Built to the original specifications by Omix-ADA.
  • Stock length
  • Non-CV design
  • Does not require a slip yoke eliminator
  • Limited five year warranty.

Driveline checks on a CJ

A front drive shaft turns the front axle whenever four-wheel drive is engaged, and its joints take the angle changes that come with suspension travel and steering. Over time the joints wear, the shaft can develop vibration, and the yokes at each end can loosen. Because drivetrain failures can be sudden, inspect the shaft, the transfer case yoke and the axle yoke whenever the drive shaft is out.

After installation, check the shaft angle at both ends and look for binding through the full range of suspension travel. Listen for vibration on the first drive at low and higher speed, and stop if a clunk or vibration develops. Retorque the fasteners after the first miles and again after hard off-road use.

  • Inspect the transfer case and axle yokes for wear
  • Check joint play and grease condition
  • Listen for vibration during the first drive

Specifications

Brand Omix-ADA
Part number 16950.06 (also shown as OAI16950.06)
Product type Front drive shaft (CJ drive shafts)
Position Front
Length Stock
Joint type Non-CV
Slip yoke eliminator Not required
Fitment type Direct fit
Warranty Limited five year warranty.

Vehicle fitment

The manufacturer fitment list for the Omix-ADA 16950.06 front drive shaft covers these vehicles: 1982–1983 Jeep CJ5 (Base, Laredo, Limited, Renegade); 1982–1986 Jeep CJ7 (Base, Laredo, Limited, Renegade).

It fits only the 1982–1983 CJ5 and 1982–1986 CJ7 in the trims named above. Other CJ5 and CJ7 years and other Jeep models fall outside that range. Confirm fit for your vehicle’s year, model and trim before ordering.

Installation notes

Follow the vehicle’s service manual and tighten all fasteners to the specifications for your model.

  • Check the part against your vehicle before starting work.
  • Re-check fasteners after the first miles of driving, and again after hard off-road use.
  • Drivetrain parts are safety-relevant; professional installation is recommended if you are not experienced.
  • Support the vehicle securely on stands, and check the drive shaft angles and joint condition after installation.
  • Check the transfer case and axle yokes for wear while the original shaft is out, and listen for vibration on the first drive.

What’s included

One front drive shaft.

Not included: U-joints, yokes and hardware are not included with the shaft.

Fitment

VehicleYearsTrims
Jeep CJ51982–1983Base, Laredo, Limited, Renegade
Jeep CJ71982–1986Base, Laredo, Limited, Renegade

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

What vehicles does the Omix-ADA 16950.06 drive shaft fit?

It fits the 1982–1983 Jeep CJ5 and the 1982–1986 Jeep CJ7, in Base, Laredo, Limited and Renegade trims. Confirm fit for your vehicle's year, model and trim before ordering.

Does the 16950.06 need a slip yoke eliminator?

No. It is a stock-length, non-CV front drive shaft and does not require a slip yoke eliminator. It is intended as a direct OE replacement for the CJ5 and CJ7 models it fits.

Is the Omix-ADA 16950.06 a front or rear drive shaft?

It is a front drive shaft. Its position is front, with stock length and a non-CV design, for Jeep CJ5 and CJ7 applications.

What warranty comes with the Omix-ADA 16950.06?

Yes. It carries a limited five year warranty and is built as a direct OE replacement. Keep your order paperwork for full warranty terms.

How do I tell if the front drive shaft needs replacing?

Look for clunking when shifting into four-wheel drive, vibration that rises with speed, or play in a universal joint. Any of these signs means the shaft should be inspected and replaced if a joint or yoke is worn.

Ready to order?

Order this part on Amazon and check out with your Amazon account. Amazon handles delivery and returns.

Buy on Amazon