Overview
The Crown Automotive 5253000 is a front caliper bolt for Jeep Cherokee (XJ), Comanche, Grand Cherokee, Commander, Liberty (KJ) and Wrangler (YJ, TJ and LJ) models listed by the manufacturer.
A caliper bolt fastens the brake caliper or its slider to the mounting bracket. This one is for the front position and is sold as a single bolt. It fits a long run of Jeep models from the Wrangler YJ through the Grand Cherokee WK.
About this part
Caliper bolts hold the caliper, or its sliding pins, to the bracket, so they carry braking load. A single front bolt covers one spot only, so work on a full axle may need more than one. Jeep used shared brake designs across several generations, so the same bolt can fit different models.
Key features
- Front caliper bolt
- Sold as one individual bolt
- Direct fit replacement
- Wide fitment list across Jeep XJ, ZJ, WJ, KJ, TJ, LJ and YJ models
Torque and inspection
Caliper bolts take high load every time the brakes are applied, and the threads sit in a spot that gets hot and dirty. When a bolt is removed, look at the threads and the bolt head for rust, stretching or a rounded hex. A damaged bolt should be replaced rather than reused, because a stretched bolt can loosen under braking and let the caliper shift.
Tighten to the torque value for your vehicle on clean threads and a clean bracket face. Threadlocker is sometimes used on caliper hardware, so check whether your setup calls for it. After the first few drives, re-check the bolts and look for any movement at the bracket. Brake hoses and slide pins are often inspected at the same time, since they sit close to the same mounting point.
- Replace bolts with rounded heads or stretched shanks
- Clean threads and the bracket face before fitting
- Re-check torque after the first few drives
- Inspect slide pins and boots while the bolts are out
Specifications
| Brand | Crown Automotive |
|---|---|
| Part number | 5253000 |
| UPC | 848399010688 |
| Product type | Caliper bolt |
| Brake position | Front |
| Quantity | Individual bolt |
| Fitment type | Direct fit |
Vehicle fitment
The manufacturer fitment list for the Crown Automotive 5253000 includes the following vehicles and trims:
- 1990–2001 Jeep Cherokee (XJ) (Base, Briarwood, Classic, Country, Laredo, Limited, Pioneer, SE, Sport)
- 1990–1992 Jeep Comanche (Base, Eliminator, Pioneer)
- 2006–2010 Jeep Commander (XK) (65th Anniversary Edition, Base, Limited, Overland, Sport)
- 2005 Jeep Grand Cherokee (WJ) (Laredo, Limited)
- 2006–2010 Jeep Grand Cherokee (WK) (65th Anniversary Edition, Laredo, Limited, Overland)
- 1993–1998 Jeep Grand Cherokee (ZJ) (5.9 Limited, Base, Laredo, Limited, Orvis, SE, TSi)
- 2003–2007 Jeep Liberty (KJ) (65th Anniversary Edition, Limited, Renegade, Rocky Mountain Edition, Sport)
- 2004–2006 Jeep Wrangler (LJ) (Unlimited, Unlimited Rubicon)
- 1997–2006 Jeep Wrangler (TJ) (65th Anniversary Edition, Rubicon, SE, Sahara, Sport, X)
- 1990–1995 Jeep Wrangler (YJ) (Base, Islander, Laredo, Renegade, Rio Grande, S, SE, Sahara)
The list is limited to the years shown for each model; it does not include the JK or JL Wrangler. Confirm your vehicle’s year, model and trim before ordering.
What’s included
One caliper bolt.
Not included: Caliper sleeves, a second bolt and other caliper hardware are not included. Check the package contents against your installation before starting.












